參數資料
型號： XRT75R06IB
廠商： Exar Corporation
文件頁數： 32/63頁
文件大?。?/td> 0K
描述： IC LIU E3/DS3/STS-1 6CH 217BGA
標準包裝： 126
類型： 線路接口裝置（LIU）
驅動器/接收器數： 6/6
規程： DS3，E3，STS-1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 217-BBGA
供應商設備封裝： 217-BGA（23x23）
包裝： 托盤
XRT75R06
á
REV. 1.0.0
SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
35
5.0
JITTER
There are three fundamental parameters that describe circuit performance relative to jitter
Jitter Tolerance
Jitter Transfer
Jitter Generation
5.1
JITTER TOLERANCE
Jitter tolerance is a measure of how well a Clock and Data Recovery unit can successfully recover data in the
presence of various forms of jitter. It is characterized by the amount of jitter required to produce a specified bit
error rate. The tolerance depends on the frequency content of the jitter. Jitter Tolerance is measured as the
jitter amplitude over a jitter spectrum for which the clock and data recovery unit achieves a specified bit error
rate (BER). To measure the jitter tolerance as shown in Figure 26, jitter is introduced by the sinusoidal
modulation of the serial data bit sequence.
Input jitter tolerance requirements are specified in terms of
compliance with jitter mask which is represented as a combination of points. Each point corresponds to a
minimum amplitude of sinusoidal jitter at a given jitter frequency.
5.1.1
DS3/STS-1 Jitter Tolerance Requirements
Bellcore GR-499 CORE specifies the minimum requirement of jitter tolerance for Category I and Category II.
The jitter tolerance requirement for Category II is the most stringent. Figure 27 shows the jitter tolerance curve
as per GR-499 specification.
FIGURE 26. JITTER TOLERANCE MEASUREMENTS
FREQ
Synthesizer
Pattern
Generator
DUT
XRT75R06
Error
Detector
Modulation
Freq.
Data
Clock
相關PDF資料
PDF描述
VE-B1T-MW-F4 CONVERTER MOD DC/DC 6.5V 100W
XRT75L02DIVTR-F IC LIU E3/DS3/STS-1 2CH 100TQFP
VI-23V-IU-F4 CONVERTER MOD DC/DC 5.8V 200W
IDT72V841L15PFG IC FIFO SYNC DUAL 15NS 64-TQFP
VE-B1T-MW-F2 CONVERTER MOD DC/DC 6.5V 100W
相關代理商/技術參數
參數描述
XRT75R06IB208 制造商:Exar Corporation 功能描述:Line Interface Unit 51.84Mbps DS3/E3/STS-1 Parallel 217-Pin BGA
XRT75R06IB-F 功能描述:外圍驅動器與原件 - PCI 6 Channel 3.3V-5V temp -45 to 85C RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT75R12 制造商:EXAR 制造商全稱:EXAR 功能描述:TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
XRT75R12_07 制造商:EXAR 制造商全稱:EXAR 功能描述:TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
XRT75R12_0710 制造商:EXAR 制造商全稱:EXAR 功能描述:TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*