TRANSMIT " />
參數資料
型號： XRT75R06DIB
廠商： Exar Corporation
文件頁數： 33/105頁
文件大?。?/td> 0K
描述： IC LIU E3/DS3/STS-1 6CH 217BGA
標準包裝： 126
類型： 線路接口裝置（LIU）
驅動器/接收器數： 6/6
規程： DS3，E3，STS-1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 217-BBGA
供應商設備封裝： 217-BGA（23x23）
包裝： 托盤
á
XRT75R06D
SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
REV. 1.0.0
28
4.4
TRANSMIT PULSE SHAPER
The Transmit Pulse Shaper converts the B3ZS encoded digital pulses into a single analog Alternate Mark
Inversion (AMI) pulse that meets the industry standard mask template requirements for STS-1 and DS3. For
E3 mode, the pulse shaper converts the HDB3 encoded pulses into a single full amplitude square shaped
pulse with very little slope. The Pulse Shaper Block also includes a Transmit Build Out Circuit, which can
either be disabled or enabled by setting the TxLEV_n bit to “1” or “0” in the control register. For DS3/STS-1
rates, the Transmit Build Out Circuit is used to shape the transmit waveform that ensures that transmit pulse
template requirements are met at the Cross-Connect system. The distance between the transmitter output and
the Cross-Connect system can be between 0 to 450 feet. For E3 rate, since the output pulse template is
measured at the secondary of the transformer and since there is no Cross-Connect system pulse template
requirements, the Transmit Build Out Circuit is always disabled. The differential line driver increases the
transmit waveform to appropriate level and drives into the 75
load as shown in Figure 21.
FIGURE 21. TRANSMIT PULSE SHAPE TEST CIRCUIT
4.4.1
Guidelines for using Transmit Build Out Circuit
If the distance between the transmitter and the DSX3 or STSX-1, Cross-Connect system, is less than 225 feet,
enable the Transmit Build Out Circuit by setting the TxLEV_n control bit to “0”. If the distance between the
transmitter and the DSX3 or STSX-1 is greater than 225 feet, disable the Transmit Build Out Circuit.
FIGURE 20. HDB3 ENCODING FORMAT
0
00
0
1
V
B
V
1
00
0
00
V
0
00
TClk
Line
Signal
TPDATA
TTIP(n)
TRing(n)
1:1
R3
75
TxPOS(n)
TxNEG(n)
TxLineClk(n)
TPData(n)
TNData(n)
TxClk(n)
31.6
+ 1%
31.6
+1%
R1
R2
相關PDF資料
PDF描述
VI-B1T-MW-F1 CONVERTER MOD DC/DC 6.5V 100W
VI-23X-IU-F4 CONVERTER MOD DC/DC 5.2V 200W
IDT72V3623L10PF IC FIFO SYNC 1KX9 10NS 128QFP
IDT72V835L15PF IC FIFO SYNC 2048X18 128QFP
XRT75L04IV IC LIU E3/DS3/STS-1 4CH 176LQFP
相關代理商/技術參數
參數描述
XRT75R06DIB-F 功能描述:網絡控制器與處理器 IC 6 Channel 3.3V-5V temp -45 to 85C RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT75R06ES 功能描述:時鐘合成器/抖動清除器 6CH T3/E3/STS1LIU+JA 3.3V W/REDUNDANCY RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75R06IB 功能描述:外圍驅動器與原件 - PCI 6CH E3/DS3/STS1 LIU+Jitter Attenuato RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT75R06IB208 制造商:Exar Corporation 功能描述:Line Interface Unit 51.84Mbps DS3/E3/STS-1 Parallel 217-Pin BGA
XRT75R06IB-F 功能描述:外圍驅動器與原件 - PCI 6 Channel 3.3V-5V temp -45 to 85C RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*