參數資料
型號： XRT75R03DIV
廠商： Exar Corporation
文件頁數： 54/135頁
文件大?。?/td> 0K
描述： IC LIU E3/DS3/STS-1 3CH 128LQFP
標準包裝： 72
類型： 線路接口裝置（LIU）
驅動器/接收器數： 3/3
規程： DS3，E3，STS-1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 128-LQFP
供應商設備封裝： 128-LQFP（14x20）
包裝： 托盤
XRT75R03D
21
REV. 1.0.4
THREE CHANNEL E3/DS3/STS-1 LINE
42
JA1
I
Jitter Attenuator Select 1:
Please see the Description above for JA0
43
JATx/Rx
I
Jitter Attenuator in Transmit/Receive Path Select Input:
This input pin is used to configure the Jitter Attenuator to operate in either the
Transmit or Receive path within each of the three (3) channels of the
XRT75R03D.
"Low" - Configures the Jitter Attenuator within each channel to operate in the
Receive Path.
"High" - Configures the Jitter Attenuator within each channel to operate in the
Transmit Path.
NOTES:
1.
The setting of this input pin applies globally to all three (3) channels of
the XRT75R03D.
2.
This input pin is ignored and should be tied to GND if the XRT75R03D
is configured to operate in the Host Mode or if the Jitter Attenuators
are disabled.
Microprocessor Serial INTERFACE - (HOST MODE)
PIN #
SIGNAL NAME
TYPE
DESCRIPTION
69
SDO/RxMON
I/O
This pin serially outputs the contents of a specified on-chip Command Register
during READ Operations via the Microprocessor Serial Interface. The data
which is output via this pin is updated upon the falling edge of the SCLK clock
signal.
This output pin will be tri-stated upon completion of a given READ operation.
NOTE: This pin functions as the RxMON input pin if the XRT75R03D has been
configured to operate in the Hardware Mode.
68
SDI/RxON
I
Microprocessor Serial Interface - Serial Data Input:
This input pin functions as the Serial Data Input pin for the Microprocessor
Serial Interface. In particular, this input pin will accept all of the following data in
a serial manner during READ and WRITE operations with the Microprocessor
Serial Interface.
The READ/WRITE indicator bit.
The Address Value of the Targeted Command Register for this particular
READ or WRITE operation.
The Data to be written into the targeted Command Register for a given
WRITE operation.
All data that is applied to this input will be sampled upon the rising edge of the
SCLK input clock signal.
NOTE: This input pin will function as the RxON input pin if the XRT75R03D has
been configured to operate in the Hardware Mode.
JITTER ATTENUATOR INTERFACE
相關PDF資料
PDF描述
ISL26710IHZ-T IC ADC 10BIT SPI/SRL 1M 8-SOT-23
MS27472T10F35SB CONN RCPT 13POS WALL MNT W/SCKT
IDT72V3656L15PF8 IC SYNC FIFO 4096X36 15NS 128QFP
IDT72V3654L15PF8 IC BI FIFO 4096X36 15NS 128QFP
MS27467T23A53P CONN PLUG 53POS STRAIGHT W/PINS
相關代理商/技術參數
參數描述
XRT75R03DIV-F 功能描述:網絡控制器與處理器 IC 3-Ch E3/DS3/STS-1 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT75R03DIVTR 功能描述:時鐘合成器/抖動清除器 3CHNNEL E3/DS3/STS 1 JITTER ATTENUATOR RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75R03DIVTR-F 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
XRT75R03ES 功能描述:時鐘合成器/抖動清除器 3CH T3/E3/STS1LIU+JA 3.3V W/REDUNDANCY RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75R03IV 功能描述:外圍驅動器與原件 - PCI 3CHNNEL E3/DS3/STS 1 JITTER ATTENUATOR RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*