參數資料
型號: XRT75R03
廠商: Exar Corporation
英文描述: THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
中文描述: Three頻道E3/DS3/STS-1線路接口單元與抖動衰減器
文件頁數: 17/92頁
文件大?。?/td> 492K
代理商: XRT75R03
xr
THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75R03
REV. 1.0.7
14
66
RxClkINV/
CS
I
Receive Clock Invert Input - Chip Selectl:
In Hardware Mode is pin is used to configure the Receive Sections of the three
(3) channels in the XRT75R03 to either output the recovered data via the
RPOS_n or RNEG_n/LCV_n output pins upon either the rising or falling edge of
the RCLK_n clock output signal.
"Low" - Configures each of the Receive Sections to output the recovered data
via the RPOS_n and RNEG_n/LCV_n output pins upon the rising edge of the
RCLK_n output clock signal.
"High" - Configures each of the Receive Sections to output the recovered data
via the RPOS_n and RNEG_n/LCV_n output pins upon the falling edge of the
RCLK_n output clock signal.
N
OTES
:
1.
This input pin will function as the CS (Chip Select Input pin) of the
Microprocessor Serial Interface when the XRT75R03 has been
configured to operate in the Host Mode.
2.
This configuration setting applies globally to all three (3) of the
channels within the XRT75R03.
3.
If the Receive Sections are configured to operate in the Single-Rail
Mode, then the LCV_n output pin will be updated on the user-selected
edge of the RCLK_n signal, per this configuration selection.
106
SFM_EN
I
Single Frequency Mode Enable:
This input pin is used to configure the XRT75R03 to operate in the SFM (Single
Frequency) Mode.
When this feature is invoked the Single-Frequency Mode Synthesizer will
become active. By applying a 12.288MHz clock signal to pin 109, STS-1CLK/
12M the XRT75R03 will, depending upon which mode the user has configured
each of the three channels, generate all of the appropriate clock signals (e.g.,
34.368MHz, 44.736MHz or 51.84. Further, the XRT75R03 internal circuitry will
route each of these synthesized clock signals to the appropriate nodes of the
corresponding three channels in the XRT75R03.
"Low" - Disables the Single Frequency Mode. In this configuration setting, the
user is required to supply to the E3CLK, DS3CLK or STS-1CLK input pins all of
the relevant clock signals that are to be used within the chip.
"High" - Enables the Single-Frequency Mode. A 12.288MHz clock signal MUST
be applied to pin 109 (STS-1CLK/12M).
N
OTE
:
This input pin is internally pulled low.
SYSTEM-SIDE RECEIVE OUTPUT AND RECEIVE CONTROL PINS
P
IN
#
S
IGNAL
N
AME
T
YPE
D
ESCRIPTION
相關PDF資料
PDF描述
XRT75R03IV THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75R06D SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
XRT75R06DIB SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
XRT75R06 SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75R06IB SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
相關代理商/技術參數
參數描述
XRT75R03D 制造商:EXAR 制造商全稱:EXAR 功能描述:THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCRONIZER
XRT75R03D_06 制造商:EXAR 制造商全稱:EXAR 功能描述:EXAR DATA SHEET FORMAT TEMPLATES
XRT75R03DES 功能描述:時鐘合成器/抖動清除器 3CH T3/E3/STS1LIU+D 3.3V W/REDUNDANCY RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75R03DIV 功能描述:時鐘合成器/抖動清除器 3CHNNEL E3/DS3/STS 1 JITTER ATTENUATOR RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75R03DIV-F 功能描述:網絡控制器與處理器 IC 3-Ch E3/DS3/STS-1 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray