參數資料
型號： XRT75L06IB-F
廠商： Exar Corporation
文件頁數： 5/63頁
文件大?。?/td> 0K
描述： IC LIU E3/DS3/STS-1 6CH 217BGA
標準包裝： 60
類型： 線路接口裝置（LIU）
驅動器/接收器數： 6/6
規程： DS3，E3，STS-1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 217-BBGA
供應商設備封裝： 217-BGA（23x23）
包裝： 托盤
XRT75L06
SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
REV. 1.0.3
10
C9
T8
D12
R11
C11
R9
RLOL_0
RLOL_1
RLOL_2
RLOL_3
RLOL_4
RLOL_5
O
Receive Loss of Lock - Channel 0:
Receive Loss of Lock - Channel 1:
Receive Loss of Lock - Channel 2:
Receive Loss of Lock - Channel 3:
Receive Loss of Lock - Channel 4:
Receive Loss of Lock - Channel 5:
This output pin toggles "High" if a Loss of Lock Condition is detected. LOL
(Loss of Lock) condition occurs if the recovered clock frequency deviates from
the Reference Clock frequency (available at either E3CLK or DS3CLK or STS-
1CLK input pins) by more than 0.5%.
L16
RXA
****
External Resistor of 3.01K
± 1%.
Should be connected between RxA and RxB for internal bias.
K16
RXB
****
External Resistor of 3.01K
±1%.
Should be connected between RxA and RxB for internal bias.
P12
ICT
I
In-Circuit Test Input:
Setting this pin "Low" causes all digital and analog outputs to go into a high-
impedance state to allow for in-circuit testing. For normal operation, tie this pin
"High".
NOTE: This pin is internally pulled up.
R12
TEST
****
Factory Test Pin
NOTE: This pin must be connected to GND for normal operation.
CONTROL AND ALARM INTERFACE
MICROPROCESSOR INTERFACE
LEAD #
SIGNAL NAME
TYPE
DESCRIPTION
K3
CS
I
Chip Select
Tie this “Low” to enable the communication with the Microprocessor Interface.
R1
PCLK
I
Processor Clock Input
To operate the Microprocessor Interface, appropriate clock frequency is pro-
vided through this pin. Maximum frequency is 66 Mhz.
K2
WR
I
Write Data :
To write data into the registers, this active low signal is asserted.
L2
RD
I
Read Data:
To read data from the registers, this active low pin is asserted.
J3
RESET
I
Register Reset:
Setting this input pin "Low" resets the contents of the Command Registers to
their default settings and default operating configuration
NOTE: This pin is internally pulled up.
L3
PMODE
I
Processor Mode Select:
When this pin is tied “High”, the microprocessor is operating in synchronous
mode which means that clock must be applied to the PCLK (pin 55).
Tie this pin “Low” to select the Asynchronous mode. An internal clock is pro-
vided for the microprocessor interface.
相關PDF資料
PDF描述
XRT75R03DIV-F IC LIU E3/DS3/STS-1 3CH 128LQFP
XRT75R03IV-F IC LIU E3/DS3/STS-1 3CH 128LQFP
XRT75R06DIB-F IC LIU E3/DS3/STS-1 6CH 217BGA
XRT75R06IB-F IC LIU E3/DS3/STS-1 6CH 217BGA
XRT75R12DIB-L IC LIU E3/DS3/STS-1 12CH 420TBGA
相關代理商/技術參數
參數描述
XRT75R03 制造商:EXAR 制造商全稱:EXAR 功能描述:THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75R03D 制造商:EXAR 制造商全稱:EXAR 功能描述:THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCRONIZER
XRT75R03D_06 制造商:EXAR 制造商全稱:EXAR 功能描述:EXAR DATA SHEET FORMAT TEMPLATES
XRT75R03DES 功能描述:時鐘合成器/抖動清除器 3CH T3/E3/STS1LIU+D 3.3V W/REDUNDANCY RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75R03DIV 功能描述:時鐘合成器/抖動清除器 3CHNNEL E3/DS3/STS 1 JITTER ATTENUATOR RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*