will send out PRBS of 2
參數資料
型號： XRT75L04DIV-F
廠商： Exar Corporation
文件頁數： 48/98頁
文件大?。?/td> 0K
描述： IC LIU E3/DS3/STS-1 4CH 176TQFP
標準包裝： 72
類型： 線路接口裝置（LIU）
驅動器/接收器數： 4/4
規程： DS3，E3，STS-1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 176-LQFP
供應商設備封裝： 176-TQFP（24x24）
包裝： 托盤
XRT75L04D
á
FOUR CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
REV. 1.0.1
48
will send out PRBS of 223-1 in E3 rate or 215-1 in STS-1/DS3 rate. At the same time, the receiver PRBS
detector is also enabled. When the correct PRBS pattern is detected by the receiver, the RNEG/LCV pin will go
“Low” to indicate PRBS synchronization has been achieved. When the PRBS detector is not in sync the
PRBSLS bit will be set to “1” and RNEG/LCV pin will go “High”.
With the PRBS mode enabled, the user can also insert a single bit error by toggling “INSPRBS” bit. This is
done by writing a “1” to INSPRBS bit. The receiver at RNEG/LCV pin will pulse “High” for one RxClk cycle for
every bit error detected. Any subsequent single bit error insertion must be done by first writing a “0” to
INSPRBS bit and followed by a “1”.
Figure 25 shows the status of RNEG/LCV pin when the XRT75L04D is configured in PRBS mode.
NOTE: In PRBS mode, the device is forced to operate in Single-Rail Mode.
8.2
LOOPBACKS:
The XRT75L04D offers three loopback modes for diagnostic purposes. In Hardware mode, the loopback
modes are selected via the RLB_n and LLB_n pins. In Host mode, the RLB_n and LLB_n bits n the Channel
control registers select the loopback modes.
8.2.1
ANALOG LOOPBACK:
In this mode, the transmitter outputs (TTIP_n and TRING_n) are connected internally to the receiver inputs
(RTIP_n and RRING_n) as shown in Figure 26. Data and clock are output at RCLK_n, RPOS_n and RNEG_n
pins for the corresponding transceiver. Analog loopback exercises most of the functional blocks of the device
including the jitter attenuator which can be selected in either the transmit or receive path.
XRT75L04D can be configured in Analog Loopback either in Hardware mode via the LLB_n and RLB_n pins or
in Host mode via LLB_n and RLB_n bits in the channel control registers.
NOTES:
1.
In the Analog loopback mode, data is also output via TTIP_n and TRING_n pins.
2.
Signals on the RTIP_n and RRING_n pins are ignored during analog loopback.
FIGURE 25. PRBS MODE
RClk
RNEG/LCV
SYNC LOSS
PRBS SYNC
Single Bit Error
相關PDF資料
PDF描述
XRT75L04IV-F IC LIU E3/DS3/STS-1 4CH 176LQFP
XRT75L06DIB-F IC LIU E3/DS3/STS-1 6CH 217BGA
XRT75L06IB-F IC LIU E3/DS3/STS-1 6CH 217BGA
XRT75R03DIV-F IC LIU E3/DS3/STS-1 3CH 128LQFP
XRT75R03IV-F IC LIU E3/DS3/STS-1 3CH 128LQFP
相關代理商/技術參數
參數描述
XRT75L04DIVTR 功能描述:時鐘合成器/抖動清除器 4 CHNL E3/DS3/STS 1 JITTER ATTENUATOR RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75L04DIVTR-F 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75L04ES 功能描述:時鐘合成器/抖動清除器 4CH T3/E3/STS1 LIU+JA 3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75L04IV 功能描述:外圍驅動器與原件 - PCI 4CH E3/DS3/STS1 JITTER ATTENUATOR RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT75L04IV-F 功能描述:外圍驅動器與原件 - PCI 4-Ch DS3, E3, STS-1 RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*