PIN
參數資料
型號： XRT75L00IV-F
廠商： Exar Corporation
文件頁數： 3/50頁
文件大?。?/td> 0K
描述： IC LIU E3/DS3/STS-1 SGL 52TQFP
標準包裝： 96
類型： 線路接口裝置（LIU）
驅動器/接收器數： 1/1
規程： DS3，E3，STS-1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 52-LQFP
供應商設備封裝： 52-TQFP（10x10）
包裝： 托盤
XRT75L00
REV. 1.0.2
E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
9
OPERATING MODE SELECT
PIN #SIGNAL NAME
TYPE
DESCRIPTION
21
HOST/(HW)I
HOST/Hardware Mode Select:
Tie this pin “High” to configure the XRT75L00 in HOST mode. Tie this “Low” to
configure in Hardware mode.
When the XRT75L00 is configured in HOST mode, the states of many discrete
input pins are ignored.
NOTE: This pin is internally pulled up.
20
E3
I
E3 Mode Select Input
A "High" on this pin configures to operate in the E3 mode.
A "Low" on this pin configures to operate in either STS-1 or DS3 mode depend-
ing on the setting on pin 19.
NOTES:
1.
This pin is internally pulled down
2.
This pin is ignored and may be tied to GND if the XRT75L00 is
configured to operate in HOST mode.
19
STS-1/DS3
I
STS-1/DS3 Select Input
A “High” on this pin configures to operate in STS-1 mode.
A “Low” on this pin configures to operate in DS3 mode.
This pin is ignored if the E3 pin is set to “High”.
NOTES:
1.
This pin is internally pulled down
2.
This pin is ignored and may be tied to GND if the XRT75L00 is
configured to operate in HOST mode.
22
SR/DR
I
Single-Rail/Dual-Rail Select:
Setting this “High” configures both the Transmitter and Receiver to operate in
Single-rail mode and also enables the B3ZS/HDB3 Encoder and Decoder. In
Single-rail mode, Transmit input at TNData should be grounded.
Setting this “Low” configures both the Transmitter and Receiver to operate in
Dual-rail mode and disables the B3ZS/HDB3 Encoder and Decoder.
NOTE: This pin is internally pulled down.
CONTROL AND ALARM INTERFACE
42
MRING
I
Monitor Ring Input
The bipolar line output signal from TRING is connected to this pin via a 270
resistor to check for line driver failure.
NOTE: This pin is internally pulled down.
41
MTIP
I
Monitor Tip Input
The bipolar line output signal from TTIP is connected to this pin via a 270-ohm
resistor to check for line driver failure.
NOTE: This pin is internally pulled down.
40
DMO
O
Drive Monitor Output
If MTIP and MRING has no transition pulse for 128 ± 32 TxClk cycles, DMO
goes “High” to indictae the driver failure. DMO output stays “High” until the next
AMI signal is detected.
相關PDF資料
PDF描述
XRT75L02DIV-F IC LIU E3/DS3/STS-1 2CH 100TQFP
XRT75L03DIV-F IC LIU E3/DS3/STS-1 3CH 128LQFP
XRT75L03IV-F IC LIU E3/DS3/STS-1 3CH 128LQFP
XRT75L04DIV-F IC LIU E3/DS3/STS-1 4CH 176TQFP
XRT75L04IV-F IC LIU E3/DS3/STS-1 4CH 176LQFP
相關代理商/技術參數
參數描述
XRT75L00IVTR 功能描述:時鐘合成器/抖動清除器 3.3V 1 CH E3/DS3/STS W/JITTER ATTEN RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75L00IVTR-F 功能描述:時鐘合成器/抖動清除器 3.3V 1 CH E3/DS3/STS W/JITTER ATTEN RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75L02 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
XRT75L02DES 功能描述:時鐘合成器/抖動清除器 2CH T3/E3/STS1 LIU+DESYNCH 3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75L02DIV-F 功能描述:網絡控制器與處理器 IC 2-Ch E3/DS3/STS-1 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*