參數資料
型號： XRT5997IV-F
廠商： Exar Corporation
文件頁數： 21/37頁
文件大?。?/td> 0K
描述： IC LIU E1 7CH 3.3V 100TQFP
標準包裝： 90
類型： 線路接口裝置（LIU）
驅動器/接收器數： 7/7
規程： E1
電源電壓： 3.14 V ~ 3.47 V
安裝類型： 表面貼裝
封裝/外殼： 100-LQFP
供應商設備封裝： 100-TQFP（14x14）
包裝： 托盤
XRT5997
28
Rev. 1.0.0
2.3
The “Peak Detector and Slicer Block
After the incoming line signal has passed through the
Receive Equalizer block, it will next be routed to the
“Slicer” block. The purpose of the “Slicer” block is to
quantify a given bit-period (or symbol) within the incom-
ing line signal as either a “1” or a “0”.
2.3
The “LOS Detector” block
The LOS Detector block, within each channel (of the
XRT5997 device) was specifically designed to comply
with the “LOS Declaration/Clearance” requirements per
ITU-T G.775. As a consequence, the channel will
declare an LOS Condition, (by driving the “RxLOS”
output pin “high”) if the received line signal amplitude
drops to –20dB or below. Further, the channel will clear
the LOS Condition if the signal amplitude rises back up
to –15dB or above. Figure 10 presents an illustration
that depicts the signal levels at which a given channel
(within the XRT5997 device) will assert and clear LOS.
0 dB
-6 dB
-9dB
-35dB
Maximum Cable Loss for E1
LOS Signal Must be Declared
LOS Signal Must be Cleared
LOS Signal may be Cleared or Declared
Figure 10. Illustration of the Signal Levels that the Receiver Sections
(within XRT5997 device) will declare and clear LOS
Timing Requirements associated with Declaring and
Clearing the LOS Indicator. The XRT5997 device was
designed to meet the ITU-T G.775 specification timing
requirements for declaring and clearing the LOS indica-
tor. In particular, the XRT5997 device will declare an
LOS, between 10 and 255 UI (or E1 bit-periods) after
the actual time the LOS condition occurred. Further,
the XRT5997 device will clear the LOS indicator within
10 to 255 UI after restoration of the incoming line
signal. Figure 11 illustrates the LOS Declaration and
Clearance behavior, in response to first, the “Loss of
Signal” event and then afterwards, the restoration of
the signal.
相關PDF資料
PDF描述
XRT6164AIP-F IC TXRX DGTL INTERFACE 16PDIP
XRT6164CD-F IC TXRX DGTL INTERFACE 16SOIC
XRT6165ID-F IC DGTL DATA PROCESSOR 24SOIC
XRT6166CD-F IC DGTL DATA PROCESSOR 28SOIC
XRT7295AEIW-F IC E3 LINE RECEIVER 20SOJ
相關代理商/技術參數
參數描述
XRT5997IVTR-F 功能描述:外圍驅動器與原件 - PCI 7 Ch. E1 LIU RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT59L81IG-F 功能描述:時鐘發生器及支持產品 BITS Clock Generator RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56
XRT59L81IGTR-F 功能描述:時鐘發生器及支持產品 BITS Clock Generator RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56
XRT59L91 制造商:EXAR 制造商全稱:EXAR 功能描述:Single-Chip E1 Line Interface Unit
XRT59L91ES 功能描述:外圍驅動器與原件 - PCI 1 CH E1 AFE RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*