參數資料
型號: XRD87L99
廠商: Exar Corporation
英文描述: LOW POWER, 2 MSPS, 10-BIT, A/D CONVERTER WITH 8-CHANNEL MUX
中文描述: 低功耗,2 MSPS的10位,在A / D轉換器8通道多路復用器
文件頁數: 14/23頁
文件大?。?/td> 414K
代理商: XRD87L99
xr
XRD87L99
LOW POWER, 2 MSPS, 10-BIT, A/D CONVERTER WITH 8-CHANNEL MUX
REV. 1.0.0
14
2.0
APPLICATION NOTES
F
IGURE
16. T
YPICAL
C
IRCUIT
C
ONNECTIONS
The following information will be useful in maximizing
the performance of the XRD87L99.
1. All signals should not exceed AV
DD
+0.5 V or
AGND -0.5 V or DV
DD
+0.5 V or DGND -0.5 V.
2. Any input pin which can see a value outside the
absolute maximum ratings (AV
DD
or DV
DD
+0.5 V
or AGND -0.5 V) should be protected by diode
clamps (HP5082-2835) from input pin to the sup-
plies. All XRD87L99 inputs have input protection
diodes which will protect the device from short
transients outside the supply ranges.
3. The design of a PC board will affect the accuracy
of XRD87L99. Use of wire wrap is not recom-
mended.
4. The analog input signal (V
IN
) is quite sensitive
and should be properly routed and terminated. It
should be shielded from the clock and digital out-
puts so as to minimize cross coupling and noise
pickup.
5. The analog input should be driven by a low
impedance (less than 50
).
6. Analog and digital ground planes should be sub-
stantial and common at one point only. The
ground plane should act as a shield for parasitics
and not a return path for signals. To reduce noise
levels, use separate low impedance ground
paths.
DGND should not be shared with other
digital circuitry
. If separate low impedance paths
cannot be provided, DGND should be connected
to AGND next to the XRD87L99.
7.
DV
DD
should not be shared with other digital cir-
cuitry
to avoid conversion errors caused by digital
supply transients. DV
DD
for the XRD87L99 should
be connected to AV
DD
next to the XRD87L99.
8. DV
DD
and AV
DD
are connected inside the
XRD87L99. DGND and AGND are connected
internally.
9. Each power supply and reference voltage pin
should be decoupled with a ceramic (0.1
μ
F) and
a tantalum (10
μ
F) capacitor as close to the
device as possible.
10. The digital output should not drive long wires.
The capacitive coupling and reflection will con-
tribute noise to the conversion. When driving dis-
tant loads, buffers should be used. 100
resis-
tors in series with the digital outputs in some
applications reduces the digital output disruption
of A
IN
.
OFW
CLK
DB9 - DB0
OE
AGND
DGND
(Substrate)
XRD87L99
AIN1
V
REF(+)
V
REF(-)
3/4 R
1/4 R
Buffer
AV
DD
DV
DD
C1D, C2D
C1A, C2A
C1 = 4.7 or 10
μ
F Tantalum
C2 = 0.1
μ
F Chip Cap or low inductance cap
R
T
= Clock Transmission Line Termination
Reference
Voltage
Source
V
REF1(-)
A
IN
C1
C2
C1
C2
C1
C2
+
-
+5 V
R
T
1 of 8
AIN8
Z < 100
Resistive
Isolation of
50 to 100
WR
CLK
A2
A1
A0
相關PDF資料
PDF描述
XRD87L99AIQ LOW POWER, 2 MSPS, 10-BIT, A/D CONVERTER WITH 8-CHANNEL MUX
XRD9810 ()
XRD9814ACV 3-Channel 14/16-Bit Linear CCD/CIS Sensor Signal Processors
XRD9816 3-Channel 16-Bit Linear CCD/CIS Sensor Signal Processors(3通道16位線性CCD/CIS 傳感信號處理器)
XRD9816ACV 3-Channel 14/16-Bit Linear CCD/CIS Sensor Signal Processors
相關代理商/技術參數
參數描述
XRD87L99AIQ 功能描述:模數轉換器 - ADC LOW POWER 2MSPS 10 BIT 8-CHANNEL RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
XRD87L99AIQ-F 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
XRD9814 制造商:EXAR 制造商全稱:EXAR 功能描述:3-Channel 14/16-Bit Linear CCD/CIS Sensor Signal Processors
XRD9814ACV 制造商:EXAR 制造商全稱:EXAR 功能描述:3-Channel 14/16-Bit Linear CCD/CIS Sensor Signal Processors
XRD9814B 制造商:EXAR 制造商全稱:EXAR 功能描述:3-Channel 14/16-Bit Linear CCD/CIS Sensor Signal Processors