REV. 1.0.1 I2C/SPI UART WITH 64-BYTE FIFO AND RS232 TRANSCEIVER PIN DESCRIPTIONS Pin Description N
參數資料
型號： XR20V2170L40-0B-EB
廠商： Exar Corporation
文件頁數： 23/49頁
文件大小： 0K
描述： EVAL BOARD FOR XR20V2170 40QFN
標準包裝： 1
系列： *
XR20V2170
3
REV. 1.0.1
I2C/SPI UART WITH 64-BYTE FIFO AND RS232 TRANSCEIVER
PIN DESCRIPTIONS
Pin Description
NAME
40-QFN
PIN #
TYPE
DESCRIPTION
I2C (SPI) INTERFACE
GPIO0
2
I/O
General purpose I/O pin. If this pin is an input and is unused, it should be con-
nected to VCC or GND. If this pin is an output and is unused, it should be left
unconnected. See IODir register.
GPIO1
5
I/O
General purpose I/O pin. If this pin is an input and is unused, it should be con-
nected to VCC or GND. If this pin is an output and is unused, it should be left
unconnected. See IODir register.
I2C/SPI#
6
I/O
I2C-bus or SPI interface select. I2C-bus interface is selected if this pin is HIGH.
SPI interface is selected if this pin is LOW
GPIO2
8
I/O
General purpose I/O pin. If this pin is an input and is unused, it should be con-
nected to VCC or GND. If this pin is an output and is unused, it should be left
unconnected. See IODir register.
XTAL1
13
I
Crystal or external clock input.
XTAL2
14
O
Crystal or buffered clock output.
GPIO3
16
I/O
General purpose I/O pin. If this pin is an input and is unused, it should be con-
nected to VCC or GND. If this pin is an output and is unused, it should be left
unconnected. See IODir register.
SDA
18
O
I2C-bus data input/output (open-drain). If SPI configuration is selected, then this
pin is undefined and must be connected to VCC.
SCL
23
I
I2C-bus or SPI serial input clock.
When the I2C-bus interface is selected, the serial clock idles HIGH. When the
SPI interface is selected, the serial clock idles LOW.
IRQ#
27
OD
Interrupt output (open-drain, active LOW).
RESET#
28
I
Reset (active LOW) - A longer than 40 ns LOW pulse on this pin will reset the
internal registers and all outputs. The UART transmitter output will be idle and
the receiver input will be ignored.
VCC
35
Pwr
2.97V to 3.63V power supply.
A0
CS#
36
I
I2C-bus device address select A0 or SPI chip select. If I2C-bus configuration is
selected, this pin along with the A1 pin allows user to change the device’s base
address. If SPI configuration is selected, this pin is the SPI chip select pin
(Schmitt-trigger, active LOW).
A1
SI
37
I
I2C-bus device address select A1 or SPI data input pin. If I2C-bus onfiguration is
selected, this pin along with A0 pin allows user to change the device’s base
address. If SPI configuration is selected, this pin is the SPI data input pin.
SO
40
O
SPI data output pin. If SPI configuration is selected then this pin is a three-state-
able output pin. If I2C-bus configuration is selected, this pin is undefined and
must be left unconnected.
相關PDF資料
PDF描述
UPJ1K390MPD6TD CAP ALUM 39UF 80V 20% RADIAL
EEU-EB2E330 CAP ALUM 33UF 250V 20% RADIAL
UPM1A391MPD1TD CAP ALUM 390UF 10V 20% RADIAL
UPS1V151MPD1TD CAP ALUM 150UF 35V 20% RADIAL
XR20V2170L40-0A-EB EVAL BOARD FOR XR20V2170 40QFN
相關代理商/技術參數
參數描述
XR20V2172 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO AND RS232 TRANSCEIVER
XR20V2172_08 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO AND RS232 TRANSCEIVER
XR20V2172IL64 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO AND RS232 TRANSCEIVER
XR20V2172IL64-F 功能描述:UART 接口集成電路 Transceiver RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR20V2172L64-0A-EB 功能描述:UART 接口集成電路 Supports V2172 64pin QFN, I2C Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*