參數資料
| 型號： | XR19L400IL40-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 28/46頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART/TXRX RS485 40QFN |
| 標準包裝： | 490 |
| 特點： | * |
| 通道數： | 1，UART |
| FIFO's： | 64 字節(jié) |
| 規(guī)程： | RS485 |
| 電源電壓： | 3.3V，5V |
| 帶自動流量控制功能： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 40-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 40-QFN 裸露焊盤（6x6） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
XR19L400
34
SINGLE CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER
REV. 1.0.3
FCTR[3]: Auto Half-Duplex Direction Control
This bit overrides the HALF/FULL# pin to enable half-duplex mode or full-duplex mode.
Logic 0 = Full-duplex mode. In this mode, the transmit interrupt is generated when the transmit holding
register becomes empty and the transmit shift register is shifting data out.
Logic 1 = Auto half-duplex mode. In this mode, the direction of the RS-485 transceiver is internally controlled
by the RTS# signal. Also, the transmit interrupt generation is delayed until the transmitter shift register
becomes empty.
FCTR[5:4]: Transmit/Receive Trigger Table Select
See
TABLE 12: TRIGGER TABLE SELECT
BIT-5
BIT-4
TABLE
0
Table-A (TX/RX)
0
1
Table-B (TX/RX)
1
0
Table-C (TX/RX)
1
Table-D (TX/RX)
Table 8 for more details.
FCTR[6]: Scratchpad Swap
Logic 0 = Scratch Pad register is selected as general read and write register. ST16C550 compatible mode.
Logic 1 = FIFO Level Count register (Read-Only), Enhanced Mode Select Register (Write-Only). Number of
characters in transmit or receive FIFO can be read via scratch pad register when this bit is set. Enhanced
Mode Select Register is selected when it is written into.
FCTR[7]: Programmable Trigger Register Select
If using both programmable TX and RX trigger levels, TX trigger levels must be set before RX trigger levels.
Logic 0 = Registers TRG and FC selected for RX.
Logic 1 = Registers TRG and FC selected for TX.
4.19
Enhanced Feature Register (EFR)
Enhanced features are enabled or disabled using this register. Bit 0-3 provide single or dual consecutive
character software flow control selection (see Table 13). When the Xon1 and Xon2 and Xoff1 and Xoff2 modes
are selected, the double 8-bit words are concatenated into two sequential characters. Caution: note that
whenever changing the TX or RX flow control bits, always reset all bits back to logic 0 (disable) before
programming a new setting.
FCTR
相關PDF資料 |
PDF描述 |
|---|---|
| XR19L402IL48-F | IC UART/TXRX RS485 48QFN |
| XR20M1170IL24TR-F | IC UART FIFO I2C/SPI 64B 24QFN |
| XR20M1172IG28-F | IC UART FIFO I2C/SPI 64B 28TSSOP |
| XR20M1280IL40-F | IC UART I2C/SPI 128 BYTE 40QFN |
| XR20V2170IL40-F | IC UART/TXRX I2C/SPI RS232 40QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR19L400IL40TR-F | 功能描述:UART 接口集成電路 Transceiver 1 Tx/1 Rx RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR19L402 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER |
| XR19L402_09 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER |
| XR19L402IL48 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER |
| XR19L402IL48-0B-EB | 功能描述:界面開發(fā)工具 Supports L402 48 pin QFN, PCI Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發(fā)布緊急采購，3分鐘左右您將得到回復。