- 您現在的位置：買賣IC網 > PDF目錄16512 > XR19L210IL40-0B-EB (Exar Corporation)EVAL BOARD FOR XR19L202 40QFN PDF資料下載
參數資料
| 型號： | XR19L210IL40-0B-EB |
| 廠商： | Exar Corporation |
| 文件頁數： | 17/43頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR XR19L202 40QFN |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
XR19L210
24
SINGLE CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER
REV. 1.0.2
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No transmit FIFO reset (default).
Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[3]: DMA Mode Select (Legacy)
This bit has no function and should be left at ’0’.
FCR[5:4]: Transmit FIFO Trigger Select
(’00’ = default, TX trigger level = 1)
These 2 bits set the trigger level for the transmit FIFO. The UART will issue a transmit interrupt when the
number of characters in the FIFO falls below the selected trigger level, or when it gets empty in case that the
FIFO did not get filled over the trigger level on last re-load. Table 8 below shows the selections. EFR bit-4 must
be set to ‘1’ before these bits can be accessed.
FCR[7:6]: Receive FIFO Trigger Select
(’00’ = default, RX trigger level =1)
These 2 bits are used to set the trigger level for the receive FIFO. The UART will issue a receive interrupt when
the number of the characters in the FIFO crosses the trigger level. Table 8 shows the selections.
4.7
Line Control Register (LCR) - Read/Write
The Line Control Register is used to specify the asynchronous data communication format. The word or
character length, the number of stop bits, and the parity are selected by writing the appropriate bits in this
register.
LCR[1:0]: TX and RX Word Length Select
These two bits specify the word length to be transmitted or received.
TABLE 8: TRANSMIT AND RECEIVE FIFO TRIGGER LEVEL SELECTION
FCR
BIT-7
FCR
BIT-6
FCR
BIT-5
FCR
BIT
-4
RECEIVE
TRIGGER LEVEL
TRANSMIT
TRIGGER LEVEL
COMPATIBILITY
0
1
0
1
0
1
1 (default)
4
8
14
16L580 and 16C580 compatible.
0
1
0
1
0
1
1 (default)
4
8
14
16L580, 16C550, 16C580, 16C554,
16C2550 and 16C2552 compatible
BIT-1
BIT-0
WORD LENGTH
0
5 (default)
0
1
6
1
0
7
1
8
相關PDF資料 |
PDF描述 |
|---|---|
| VI-252-EX | CONVERTER MOD DC/DC 15V 75W |
| 5504972-4 | CABLE ASSEM FIBER SC-ST 5 METER |
| ILSB1206ER6R8K | INDUCTOR 6.8UH 10% 1206 |
| EBC31DRTS-S13 | CONN EDGECARD 62POS .100 EXTEND |
| ILSB1206ER68NM | INDUCTOR 0.068UH 20% 1206 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR19L210IL40-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR19L212 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER |
| XR19L212IL48 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER |
| XR19L212IL48-0B-EB | 功能描述:界面開發工具 Supports L212 48 pin QFN, PCI Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR19L212IL48-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。