- 您現在的位置：買賣IC網 > PDF目錄376455 > XR17L152CM (EXAR CORP) 3.3V PCI BUS DUAL UART PDF資料下載
參數資料
| 型號： | XR17L152CM |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 3.3V PCI BUS DUAL UART |
| 中文描述： | 2 CHANNEL(S), 3.125M bps, SERIAL COMM CONTROLLER, PQFP100 |
| 封裝： | 14 X 14 MM, 1 MM HEIGHT, TQFP-100 |
| 文件頁數： | 37/55頁 |
| 文件大?。?/td> | 318K |
| 代理商： | XR17L152CM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
XR17L152
3.3V PCI BUS DUAL UART
REV. 1.1.0
á
DISCONTINUED
37
LCR[7]: Baud Rate Divisors Enable
Baud rate generator divisor (DLL/DLM) enable.
Logic 0 = Data registers are selected (default).
Logic 1 = Divisor latch registers are selected.
Modem Control Register (MCR) or General Purpose Outputs Control
The MCR register is used for controlling the serial/modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Pins
The DTR# pin may be used for automatic hardware flow control enabled by EFR bit-6 and MCR bit-2=1. If the
modem interface is not used, this output may be used for general purpose.
Logic 0 = Force DTR# output to a logic 1 (default).
Logic 1 = Force DTR# output to a logic 0.
MCR[1]: RTS# Pins
The RTS# pin may be used for automatic hardware flow control by enabled by EFR bit-6 and MCR bit-2=0. If
the modem interface is not used, this output may be used for general purpose.
Logic 0 = Force RTS# output to a logic 1 (default).
Logic 1 = Force RTS# output to a logic 0.
MCR[2]: DTR# or RTS# for Auto Flow Control
The OP1 output is not available in the XR17L152. It is present for 16C550 compatibility during internal
loopback. See
Figure 11
. Logic zero is default.
DTR# or RTS# auto hardware flow control select. This bit is in effect only when auto RTS/DTR is enabled by
EFR bit-6.
Logic 0 = Uses RTS#/CTS# pins for auto hardware flow control.
Logic 1 = Uses DTR#/DSR# pin is used for auto hardware flow control.
MCR[3]: (OP2)
The OP2 output is not available in the XR17L152. It is present for 16C550 compatibility during internal
loopback. See
Figure 11
. Logic zero is default.
MCR[4]: Internal Loopback Enable
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and
Figure 11
.
MCR[5]: Xon-Any Enable
Logic 0 = Disable Xon-Any function (for 16C550 compatibility) (default).
Logic 1 = Enable Xon-Any function. In this mode any RX character received will enable Xon, resume data
transmission.
MCR[6]: Infrared Encoder/Decoder Enable
This bit overrides the ENIR pin selection.
Logic 0 = Disable the infrared mode (default).
Logic 1 = Enable infrared IrDA receive and transmit inputs/outputs. While in this mode, the TX/RX output/
input are routed to the infrared encoder/decoder. The data input and output levels will conform to the IrDA
infrared interface requirement. As such, while in this mode the infrared TX output will be a logic 0 during idle
data conditions. FCTR bit-4 may be selected to invert the RX input signal level going to the decoder for
infrared modules that provide rather an inverted output.
相關PDF資料 |
PDF描述 |
|---|---|
| XR2001 | High-Voltage, High-Current Darlington Transistor Arrays |
| XR2002CN | High-Voltage, High-Current Darlington Transistor Arrays |
| XR2003 | High-Voltage, High-Current Darlington Transistor Arrays |
| XR2003CN | Programable Driver IC |
| XR2004 | High-Voltage, High-Current Darlington Transistor Arrays |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR17L152IM | 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V PCI BUS DUAL UART |
| XR17L154 | 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V PCI BUS QUAD UART |
| XR17L154CV | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecomm/Datacomm |
| XR17L154IV | 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V PCI BUS QUAD UART |
| XR17V252 | 制造商:EXAR 制造商全稱:EXAR 功能描述:66 MHZ PCI BUS DUAL UART WITH POWER MANAGEMENT SUPPORT |
發布緊急采購，3分鐘左右您將得到回復。