參數資料
型號: XR17C154CV
廠商: EXAR CORP
元件分類: 微控制器/微處理器
英文描述: Burner
中文描述: 4 CHANNEL(S), 6.25M bps, SERIAL COMM CONTROLLER, PQFP144
封裝: 20 X 20 MM, 1.40 MM HEIGHT, TQFP-144
文件頁數: 44/62頁
文件大小: 721K
代理商: XR17C154CV
XR17C154
5V PCI BUS QUAD UART
á
REV. 1.3.0
44
4.8.12
This is an 8-bit general purpose register for the user to store temporary data. The content of this register is
preserved during sleep mode but becomes 0xFF (default) after a reset or a power off-on cycle.
4.8.13
FEATURE CONTROL REGISTER (FCTR) - Read/Write
FCTR [3:0] - Auto RTS/DTR Flow Control Hysteresis Select
These bits select the auto RTS/DTR flow control hysteresis and only valid when TX and RX Trigger Table-D is
selected (FCTR bit-6 and 7 are set to logic 1). The RTS/DTR hysteresis is referenced to the RX FIFO trigger
level. After reset, these bits are set to logic 0 selecting the next FIFO trigger level for hardware flow control.
Table 17
shows the 16 selectable hysteresis levels.
FCTR[4]: Infrared RX Input Logic Select
Logic 0 = Select RX input as active high encoded IrDA data, normal, (default).
Logic 1 = Select RX input as active low encoded IrDA data, inverted.
FCTR[5]: Auto RS485 Enable
Auto RS485 half duplex control enable/disable.
Logic 0 = Standard ST16C550 mode. Transmitter generates an interrupt when transmit holding register
(THR) becomes empty. Transmit Shift Register (TSR) may still be shifting data bit out.
Logic 1 = Enable Auto RS485 half duplex direction control. RTS# output changes its logic level from HIGH to
LOW when finished sending the last stop bit of the last character out of the TSR register. It changes back to
HIGH from LOW when a data byte is loaded into the THR or transmit FIFO. The change to HIGH occurs prior
sending the start-bit. It also changes the transmitter interrupt from transmit holding to transmit shift register
(TSR) empty.
FCTR[7:6]: TX and RX FIFO Trigger Table Select
These 2 bits select the transmit and receive FIFO trigger level table A, B, C or D. When table A, B, or C is
selected the auto RTS flow control trigger level is set to "next FIFO trigger level" for compatibility to ST16C550
and ST16C650 series. RTS#/DTR# triggers on the next level of the RX FIFO trigger level, in another word, one
FIFO level above and one FIFO level below. See
Table 14
for complete selection with FCR bit 4-5 and FCTR
bit 6-7, i.e. if Table C is used on the receiver with RX FIFO trigger level set to 56 bytes, RTS/DTR# output will
de-assert at 60 and re-assert at 16.
SCRATCH PAD REGISTER (SPR) - Read/Write
相關PDF資料
PDF描述
XR17C154IV Tools, Heatgun; Leaded Process Compatible:No; Peak Reflow Compatible (260 C):No RoHS Compliant: No
XR17C158 PCI Bus Octal UART(八通用異步接收器/發送器(滿足通訊系統中PCI總線和高帶寬要求))
XR17D152 UNIVERSAL (3.3V AND 5V) PCI BUS DUAL UART
XR17D152CM UNIVERSAL (3.3V AND 5V) PCI BUS DUAL UART
XR17D152IM UNIVERSAL (3.3V AND 5V) PCI BUS DUAL UART
相關代理商/技術參數
參數描述
XR17C154CV-0A-EVB 功能描述:UART 接口集成電路 Supports C154 144 ld TQFP, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR17C154CV-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR17C154CVTR-F 制造商:Exar Corporation 功能描述:UART 4-CH 64Byte FIFO 5V 144-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR17C154CVTR-F
XR17C154IV 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR17C154IV-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel