REV. 1.0.4 2.25V TO 3.6V QUAD UART WITH 32-BYTE FIFO 4.6 Line Control Register (LCR) - Read/Write The Line Contr" />
參數資料
型號: XR16V564DIV-0A-EB
廠商: Exar Corporation
文件頁數: 25/54頁
文件大小: 0K
描述: EVAL BOARD FOR XR16V564D 64LQFP
標準包裝: 1
系列: *
XR16V564/564D
31
REV. 1.0.4
2.25V TO 3.6V QUAD UART WITH 32-BYTE FIFO
4.6
Line Control Register (LCR) - Read/Write
The Line Control Register is used to specify the asynchronous data communication format. The word or
character length, the number of stop bits, and the parity are selected by writing the appropriate bits in this
register.
LCR[1:0]: TX and RX Word Length Select
These two bits specify the word length to be transmitted or received.
WORD LENGTH
0
5 (default)
0
1
6
1
0
7
1
8
LCR[2]: TX and RX Stop-bit Length Select
The length of stop bit is specified by this bit in conjunction with the programmed word length.
WORD
LENGTH
STOP BIT LENGTH
(BIT TIME(S))
0
5,6,7,8
1 (default)
1
5
1-1/2
1
6,7,8
2
LCR[3]: TX and RX Parity Select
Parity or no parity can be selected via this bit. The parity bit is a simple way used in communications for data
integrity check. See Table 13 for parity selection summary below.
Logic 0 = No parity.
Logic 1 = A parity bit is generated during the transmission while the receiver checks for parity error of the
data character received.
LCR[4]: TX and RX Parity Select
If the parity bit is enabled with LCR bit-3 set to a logic 1, LCR BIT-4 selects the even or odd parity format.
Logic 0 = ODD Parity is generated by forcing an odd number of logic 1’s in the transmitted character. The
receiver must be programmed to check the same format (default).
Logic 1 = EVEN Parity is generated by forcing an even number of logic 1’s in the transmitted character. The
receiver must be programmed to check the same format.
BIT-1
BIT-0
BIT-2
相關PDF資料
PDF描述
M3BBK-1618R IDC CABLE - MSR16K/MC16M/MSR16K
CDRH2D14NP-1R5NC INDUCTOR POWER 1.5UH 2A SMD
RPP30-2424SW-F CONV DC/DC 30W 9-36VIN 24VOUT
XC61CN2202MR-G IC SUPERVISOR 2.2V SOT23-3
6374039-8 C/A 62.5/125, PLNM ZIP, SC
相關代理商/技術參數
參數描述
XR16V564DIV-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16V564DIVTR-F 制造商:Exar Corporation 功能描述:UART 4-CH 32Byte FIFO 2.5V/3.3V 64-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR16V564DIVTR-F
XR16V564IJ 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
XR16V564IJ-0A-EVB 功能描述:UART 接口集成電路 Supports V564 68 ld PLCC, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16V564IJ-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel