- 您現在的位置：買賣IC網 > PDF目錄3762 > XR16V2552IL-F (Exar Corporation)IC UART FIFO 16B DUAL 32QFN PDF資料下載
參數資料
| 型號： | XR16V2552IL-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 34/46頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO 16B DUAL 32QFN |
| 標準包裝： | 490 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 16 字節 |
| 規程： | RS232，RS422 |
| 電源電壓： | 2.25 V ~ 3.6 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 32-QFN 裸露焊盤（5x5） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
XR16V2552
4
HIGH PERFORMANCE DUART WITH 16-BYTE FIFO
REV. 1.0.3
RXA
24
39
I
UART channel A Receive Data or infrared receive data. Normal receive
data input must idle HIGH. The infrared receiver pulses typically idles
LOW but can be inverted by software control prior going in to the
decoder, see MCR[6] and MCR[2]. If this pin is not used, tie it to VCC
or pull it high via a 100k ohm resistor.
RTSA#
22
36
O
UART channel A Request-to-Send (active low) or general purpose out-
put. This output must be asserted prior to using auto RTS flow control,
see EFR[6], MCR[1] and IER[6].
CTSA#
25
40
I
UART channel A Clear-to-Send (active low) or general purpose input.
It can be used for auto CTS flow control, see EFR[7], and IER[7]. This
input should be connected to VCC when not used.
DTRA#
-
37
O
UART channel A Data-Terminal-Ready (active low) or general purpose
output. If this pin is not used, leave it unconnected.
DSRA#
-
41
I
UART channel A Data-Set-Ready (active low) or general purpose input.
This input should be connected to VCC when not used. This input has
no effect on the UART.
CDA#
-
42
I
UART channel A Carrier-Detect (active low) or general purpose input.
This input should be connected to VCC when not used. This input has
no effect on the UART.
RIA#
-
43
I
UART channel A Ring-Indicator (active low) or general purpose input.
This input should be connected to VCC when not used. This input has
no effect on the UART.
MFA#
-
35
O
Multi-Function Output Channel A. This output pin can function as the
OP2A#, BAUDOUTA#, or RXRDYA# pin. One of these output signal
functions can be selected by the user programmable bits 1-2 of the
Alternate Function Register (AFR). These signal functions are
described as follows:
1) OP2A# - When OP2A# (active low) is selected, the MF# pin is LOW
when MCR bit-3 is set to a logic 1 (see MCR bit-3). MCR bit-3 defaults
to a logic 0 condition after a reset or power-up.
2) BAUDOUTA# - When BAUDOUTA# function is selected, the Baud
rate clock output is available at this pin.
3) RXRDYA# - RXRDYA# (active low) is intended for monitoring block
data transfers. See
Table 2 for more details.
TXB
16
26
O
UART channel B Transmit Data or infrared encoder data. Standard
transmit and receive interface is enabled when MCR[6] = 0. In this
mode, the TX signal will be HIGH during reset or idle (no data). Infrared
IrDA transmit and receive interface is enabled when MCR[6] = 1. In the
Infrared mode, the inactive state (no data) for the Infrared encoder/
decoder interface is LOW. If it is not used, leave it unconnected.
RXB
15
25
I
UART channel B Receive Data or infrared receive data. Normal receive
data input must idle HIGH. The infrared receiver pulses typically idles
LOW but can be inverted by software control prior going in to the
decoder, see MCR[6] and MCR[2]. If this pin is not used, tie it to VCC
or pull it high via a 100k ohm resistor.
RTSB#
13
23
O
UART channel B Request-to-Send (active low) or general purpose out-
put. This port must be asserted prior to using auto RTS flow control,
see EFR[6], MCR[1], and IER[6].
Pin Description
NAME
32-QFN
PIN #
44-PLCC
PIN #
TYPE
DESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| XR16L2552IM-F | IC UART FIFO 16B DUAL 48TQFP |
| XR16L2550IL-F | IC UART FIFO 16B DUAL 32QFN |
| ST16C2552CJ44TR-F | IC UART FIFO 16B DUAL 44PLCC |
| ST78C36CJ44-F | IC UART FIFO 16B 44PLCC |
| ST16C580CQ48-F | IC UART FIFO 16B 48TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16V2650 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 32-BYTE FIFO |
| XR16V2650_07 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 32-BYTE FIFO |
| XR16V2650IL | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| XR16V2650IL-0B-EB | 功能描述:UART 接口集成電路 Supports V2650 32pin QFN, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16V2650IL32 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 32-BYTE FIFO |
發布緊急采購，3分鐘左右您將得到回復。