- 您現在的位置：買賣IC網 > PDF目錄16524 > XR16V2551IL-0B-EB (Exar Corporation)EVAL BOARD FOR V2551 32QFN PDF資料下載
參數資料
| 型號： | XR16V2551IL-0B-EB |
| 廠商： | Exar Corporation |
| 文件頁數： | 25/49頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR V2551 32QFN |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
TABLE 13: PARITY SELECTION
LCR BIT-5 LCR BIT-4 LCR BIT-3
PARITY SELECTION
X
0
No parity
0
1
Odd parity
0
1
Even parity
1
0
1
Force parity to mark, “1”
1
Forced parity to space, “0”
XR16V2551
31
REV. 1.0.3
HIGH PERFORMANCE DUART WITH 16-BYTE FIFO AND POWERSAVE FEATURE
LCR[6]: Transmit Break Enable
When enabled, the Break control bit causes a break condition to be transmitted (the TX output is forced to a
“space", LOW state). This condition remains, until disabled by setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition (default).
Logic 1 = Forces the transmitter output (TX) to a “space”, LOW, for alerting the remote receiver of a line
break condition.
LCR[7]: Baud Rate Divisors Enable
Baud rate generator divisor (DLL, DLM and DLD) enable.
Logic 0 = Data registers are selected (default).
Logic 1 = Divisor latch registers are selected.
4.7
Modem Control Register (MCR) or General Purpose Outputs Control - Read/Write
The MCR register is used for controlling the serial/modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Output
The DTR# pin is a modem control output. If the modem interface is not used, this output may be used as a
general purpose output.
Logic 0 = Force DTR# output HIGH (default).
Logic 1 = Force DTR# output LOW.
MCR[1]: RTS# Output
The RTS# pin is a modem control output and may be used for automatic hardware flow control by enabled by
EFR bit-6. If the modem interface is not used, this output may be used as a general purpose output.
Logic 0 = Force RTS# HIGH (default).
Logic 1 = Force RTS# LOW.
MCR[2]: IrDA RX Inversion or OP1# (legacy term)
When Infrared mode is enabled (MCR[6]=1 and EFR[4]=1), this bit selects the idle state of the encoded IrDA
data. In internal loopback mode, this bit functions like the OP1# in the 16C550.
Logic 0 = Select RX input as active-low encoded IrDA data (Idle state will be low) (default).
Logic 1 = Select RX input as active-high encoded IrDA data (Idle state will be high).
In the Internal Loopback Mode, this bit controls the state of the modem input RI# bit in the MSR register as
shown in Figure 12.
相關PDF資料 |
PDF描述 |
|---|---|
| 6374109-4 | C/A 62.5/125 1.6MM LC 4M |
| GEM36DTAH | CONN EDGECARD 72POS R/A .156 SLD |
| UUX1H330MNL1GS | CAP ALUM 33UF 50V 20% SMD |
| GEM36DTAD | CONN EDGECARD 72POS R/A .156 SLD |
| VE-JV4-EZ-S | CONVERTER MOD DC/DC 48V 25W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16V2551IL32 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 16-BYTE FIFO AND POWERSAVE FEATURE |
| XR16V2551IL-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16V2551ILTR-F | 制造商:Exar Corporation 功能描述:UART 2-CH 16Byte FIFO 2.5V/3.3V 32-Pin QFN EP T/R 制造商:Exar Corporation 功能描述:XR16V2551ILTR-F |
| XR16V2551IM | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| XR16V2551IM-0B-EB | 功能描述:UART 接口集成電路 Supports V2551 48 ld TQFP, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。