REV. 1.0.1 2.10 Auto RTS (Hardware) Flow Control Automatic R" />
參數資料
型號： XR16M781IL32-0C-EB
廠商： Exar Corporation
文件頁數： 8/52頁
文件大?。?/td> 0K
描述： EVAL BOARD FOR XR16M781-C 32QFN
標準包裝： 1
系列： *
XR16M781
16
1.62V TO 3.63V UART WITH 64-BYTE FIFO AND VLIO INTERFACE
REV. 1.0.1
2.10
Auto RTS (Hardware) Flow Control
Automatic RTS hardware flow control is used to prevent data overrun to the local receiver FIFO. The RTS#
output is used to request remote unit to suspend/resume data transmission. The auto RTS flow control
features is enabled to fit specific application requirement (see Figure 12):
Enable auto RTS flow control using EFR bit-6.
The auto RTS function must be started by asserting RTS# output pin (MCR bit-1 to logic 1 after it is enabled).
If using the Auto RTS interrupt:
Enable RTS interrupt through IER bit-6 (after setting EFR bit-4). The UART issues an interrupt when the
RTS# pin makes a transition from low to high: ISR bit-5 will be set to logic 1.
2.11
Auto RTS Hysteresis
With the Auto RTS function enabled, an interrupt is generated when the receive FIFO reaches the selected RX
trigger level. The RTS# pin will not be forced HIGH (RTS off) until the receive FIFO reaches one trigger level
above the selected trigger level in the trigger table (Table 9). The RTS# pin will return LOW after the RX FIFO
is unloaded to one level below the selected trigger level. Under the above described conditions, the M781 will
continue to accept data until the receive FIFO gets full. The Auto RTS function is initiated when the RTS#
output pin is asserted LOW (RTS On).
TABLE 4: AUTO RTS (HARDWARE) FLOW CONTROL
RX TRIGGER LEVEL
INT PIN ACTIVATION
RTS# DE-ASSERTED (HIGH)
(CHARACTERS IN RX FIFO)
RTS# ASSERTED (LOW)
(CHARACTERS IN RX FIFO)
8
16
0
16
56
8
56
60
16
60
56
2.12
Auto CTS Flow Control
Automatic CTS flow control is used to prevent data overrun to the remote receiver FIFO. The CTS# input is
monitored to suspend/restart the local transmitter. The auto CTS flow control feature is selected to fit specific
application requirement (see Figure 12):
Enable auto CTS flow control using EFR bit-7.
If needed, the CTS interrupt can be enabled through IER bit-7 (after setting EFR bit-4). The UART issues an
interrupt when the CTS# pin is de-asserted (HIGH): ISR bit-5 will be set to 1, and UART will suspend
相關PDF資料
PDF描述
ACM06DRYH CONN EDGECARD 12POS DIP .156 SLD
D-500-L455-3-612-120 MICROCOUPLER 3 STUB SHIELD CABLE
XR16M770IL24-0C-EB EVAL BOARD FOR XR16M770-C 24QFN
H3DWH-5006G IDC CABLE - HKR50H/AE50G/HPL50H
M3TKK-1006R IDC CABLE - MSD10K/MC10M/MPK10K
相關代理商/技術參數
參數描述
XR16M781IL32-F 功能描述:UART 接口集成電路 1.62-3.63V; 64-Byte FIFO & VLIO; UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16M890 制造商:EXAR 制造商全稱:EXAR 功能描述:Single-Channel UARTs with Selectable Bus Interfaces
XR16M890_11 制造商:EXAR 制造商全稱:EXAR 功能描述:UART WITH 128-BYTE FIFO AND INTEGRATED LEVEL SHIFTERS
XR16M890IL32 制造商:EXAR 制造商全稱:EXAR 功能描述:UART WITH 128-BYTE FIFO AND INTEGRATED LEVEL SHIFTERS
XR16M890IL32-0C-EB 功能描述:UART 接口集成電路 EVAL F/M890 32QFN MOT, INTEL, VLIO INT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*