參數資料
型號： XR16M2752IL32-F
廠商： Exar Corporation
文件頁數： 24/51頁
文件大?。?/td> 0K
描述： IC UART FIFO 64B DUAL 32QFN
標準包裝： 490
特點： *
通道數： 2，DUART
FIFO's： 64 字節
規程： RS232，RS485
電源電壓： 1.62 V ~ 3.63 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 32-VFQFN 裸露焊盤
供應商設備封裝： 32-QFN 裸露焊盤（5x5）
包裝： 托盤
XR16M2752
30
1.62V TO 3.63V HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
REV. 1.0.0
LCR[6]: Transmit Break Enable
When enabled, the Break control bit causes a break condition to be transmitted (the TX output is forced to a
“space", LOW state). This condition remains, until disabled by setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition (default).
Logic 1 = Forces the transmitter output (TX) to a “space”, LOW, for alerting the remote receiver of a line
break condition.
LCR[7]: Baud Rate Divisors Enable
Baud rate generator divisor (DLL, DLM and DLD) enable.
Logic 0 = Data registers are selected (default).
Logic 1 = Divisor latch registers are selected.
4.7
Modem Control Register (MCR) or General Purpose Outputs Control - Read/Write
The MCR register is used for controlling the serial/modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Output
The DTR# pin is a modem control output. If the modem interface is not used, this output may be used as a
general purpose output.
Logic 0 = Force DTR# output HIGH (default).
Logic 1 = Force DTR# output LOW.
MCR[1]: RTS# Output
The RTS# pin is a modem control output and may be used for automatic hardware flow control by enabled by
EFR bit-6. The RTS# pin can also be used for Auto RS485 Half-Duplex direction control enabled by FCTR bit-
3. If the modem interface is not used, this output may be used as a general purpose output.
Logic 0 = Force RTS# HIGH (default).
Logic 1 = Force RTS# LOW.
MCR[2]: Reserved
OP1# is not available as an output pin on the M2752. But it is available for use during Internal Loopback Mode.
In the Loopback Mode, this bit is used to write the state of the modem RI# interface signal.
MCR[3]: OP2# Output
OP2# is available as an output pin on the M2752 when AFR[2:1] = ‘00’. In the Loopback Mode, MCR[3] is used
to write the state of the modem CD# interface signal. Also see pin descriptions for MF# pins.
Logic 0 = Forces OP2# output HIGH (default).
Logic 1 = Forces OP2# output LOW.
MCR[4]: Internal Loopback Enable
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and Figure 12.
MCR[5]: Xon-Any Enable (requires EFR bit-4 = 1)
Logic 0 = Disable Xon-Any function (default).
Logic 1 = Enable Xon-Any function. In this mode, any RX character received will resume transmit operation.
The RX character will be loaded into the RX FIFO, unless the RX character is an Xon or Xoff character and
the M2752 is programmed to use the Xon/Xoff flow control.
相關PDF資料
PDF描述
XR16M2750IL32-F IC UART FIFO 64B DUAL 32QFN
ST16C452CJ68PS-F IC UART W/PAR PORT DUAL 68PLCC
ST16C2450CQ48-F IC UART FIFO DUAL 48TQFP
XR16C2550IM-F IC UART FIFO 16B DUAL 48TQFP
XR88C92IJTR-F IC UART FIFO DUAL 44PLCC
相關代理商/技術參數
參數描述
XR16M2752IL32TR-F 制造商:Exar Corporation 功能描述:UART 2-CH 64Byte FIFO 1.8V/2.5V/3.3V 32-Pin QFN EP T/R 制造商:Exar Corporation 功能描述:XR16M2752IL32TR-F
XR16M554 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 16-BYTE FIFO
XR16M554D 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 16-BYTE FIFO
XR16M554DIV-0A-EVB 功能描述:界面開發工具 Eval Board for XR16M554DIV Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR16M554DIV-0B-EVB 功能描述:界面開發工具 Eval Board for XR16M554DIV Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*