- 您現在的位置：買賣IC網 > PDF目錄1975 > XR16M2650IM48-F (Exar Corporation)IC UART FIFO 32B DUAL 48TQFP PDF資料下載
參數資料
| 型號： | XR16M2650IM48-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 11/47頁 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 32B DUAL 48TQFP |
| 標準包裝： | 250 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 32 字節 |
| 規程： | RS232，RS422 |
| 電源電壓： | 1.62 V ~ 3.63 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-TQFP |
| 供應商設備封裝： | 48-TQFP（7x7） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
XR16M2650
19
REV. 1.0.2
HIGH PERFORMANCE LOW VOLTAGE DUART WITH 32-BYTE FIFO
2.18
Sleep Mode with Auto Wake-Up
The M2650 supports low voltage system designs, hence, a sleep mode is included to reduce its power
consumption when the chip is not actively used.
All of these conditions must be satisfied for the M2650 to enter sleep mode:
■ no interrupts pending for both channels of the M2650 (ISR bit-0 = 1)
■ sleep mode of both channels are enabled (IER bit-4 = 1)
■ modem inputs are not toggling (MSR bits 0-3 = 0)
■ RX input pins are idling HIGH
The M2650 stops its crystal oscillator to conserve power in the sleep mode. User can check the XTAL2 pin for
no clock output as an indication that the device has entered the sleep mode.
The M2650 resumes normal operation by any of the following:
■ a receive data start bit transition (HIGH to LOW)
■ a data byte is loaded to the transmitter, THR or FIFO
■ a change of logic state on any of the modem or general purpose serial inputs: CTS#, DSR#, CD#, RI#
If the M2650 is awakened by any one of the above conditions, it will return to the sleep mode automatically
after all interrupting conditions have been serviced and cleared. If the M2650 is awakened by the modem
inputs, a read to the MSR is required to reset the modem inputs. In any case, the sleep mode will not be
entered while an interrupt is pending from channel A or B. The M2650 will stay in the sleep mode of operation
until it is disabled by setting IER bit-4 to LOW.
If the address lines, data bus lines, IOW#, IOR#, CSA#, CSB#, and modem input lines remain steady when the
M2650 is in sleep mode, the maximum current will be in the microamp range as specified in the DC Electrical
Characteristics on page 36. If the input lines are floating or are toggling while the M2650 is in sleep mode, the
current can be up to 100 times more. If any of those signals are toggling or floating, then an external buffer
would be required to keep the address, data and control lines steady to achieve the low current. As an
alternative, please refer to the XR16V2651 which is pin-to-pin and software compatible with the M2650 but with
some additional pins and the PowerSave feature that eliminates any unnecessary external buffer.
A word of caution: owing to the starting up delay of the crystal oscillator after waking up from sleep mode, the
first few receive characters may be lost. The number of characters lost during the restart also depends on your
operating data rate. More characters are lost when operating at higher data rate. Also, it is important to keep
RX A/B inputs idling HIGH or “marking” condition during sleep mode to avoid receiving a “break” condition
upon the restart. This may occur when the external interface transceivers (RS-232, RS-422 or another type)
are also put to sleep mode and cannot maintain the “marking” condition. To avoid this, the designer can use a
47k-100k ohm pull-up resistor on the RXA and RXB pins.
相關PDF資料 |
PDF描述 |
|---|---|
| XR16M2651IM48-F | IC UART FIFO 32B DUAL 48TQFP |
| XR16M2750IM48-F | IC UART FIFO 64B DUAL 48TQFP |
| XR16M2751IM48-F | IC UART FIFO 64B DUAL 48TQFP |
| XR16M2752IJ44-F | IC UART FIFO 64B DUAL 44PLCC |
| XR16M554IV64-F | IC UART FIFO 16B QUAD 64LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16M2651 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 32-BYTE FIFO AND POWERSAVE FEATURE |
| XR16M2651IL-0B-EB | 功能描述:UART 接口集成電路 Supports M2651 32pin QFN, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16M2651IL32 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| XR16M2651IL32-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16M2651IL32TR-F | 制造商:Exar Corporation 功能描述:UART 2-CH 32Byte FIFO 1.8V/2.5V/3.3V 32-Pin QFN EP T/R 制造商:Exar Corporation 功能描述:XR16M2651IL32TR-F |
發布緊急采購，3分鐘左右您將得到回復。