- 您現在的位置：買賣IC網 > PDF目錄3766 > XR16L2751IM-F (Exar Corporation)IC UART FIFO 64B DUAL 48TQFP PDF資料下載
參數資料
| 型號： | XR16L2751IM-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 26/50頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO 64B DUAL 48TQFP |
| 標準包裝： | 250 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 64 字節 |
| 規程： | RS232，RS485 |
| 電源電壓： | 2.25 V ~ 5.5 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-TQFP |
| 供應商設備封裝： | 48-TQFP（7x7） |
| 包裝： | 托盤 |
| 其它名稱： | 1016-1452 XR16L2751IM-F-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
XR16L2751
2.25V TO 5.5V DUART WITH 64-BYTE FIFO AND POWERSAVE
REV. 1.2.3
32
MCR[6]: Infrared Encoder/Decoder Enable
Logic 0 = Enable the standard modem receive and transmit input/output interface. (Default)
Logic 1 = Enable infrared IrDA receive and transmit inputs/outputs. The TX/RX output/input are routed to the
infrared encoder/decoder. The data input and output levels conform to the IrDA infrared interface
requirement. While in this mode, the infrared TX output will be a logic 0 during idle data conditions.
MCR[7]: BRG Clock Prescaler Select
The 2751 has a hardware pin (pin 25) to select this function upon power up or reset. After the power up or
reset, this register bit will have control and can alter the logic state.
Logic 0 = Divide by one. The input clock from the crystal or external clock is fed directly to the Programmable
Baud Rate Generator without further modification, i.e., divide by one (default).
Logic 1 = Divide by four. The prescaler divides the input clock from the crystal or external clock by four and
feeds it to the Programmable Baud Rate Generator, hence, data rates become one forth.
4.8
Line Status Register (LSR) - Read Only
This register provides the status of data transfers between the UART and the host.
LSR[0]: Receive Data Ready Indicator
Logic 0 = No data in receive holding register or FIFO (default).
Logic 1 = Data has been received and is saved in the receive holding register or FIFO.
LSR[1]: Receiver Overrun Flag
Logic 0 = No overrun error. (default)
Logic 1 = Overrun error. A data overrun error condition occurred in the receive shift register. This happens
when additional data arrives while the FIFO is full. In this case the previous data in the receive shift register
is overwritten. Note that under this condition the data byte in the receive shift register is not transferred into
the FIFO, therefore the data in the FIFO is not corrupted by the error.
LSR[2]: Receive Data Parity Error Flag
Logic 0 = No parity error (default).
Logic 1 = Parity error. The receive character in RHR does not have correct parity information and is suspect.
This error is associated with the character available for reading in RHR.
LSR[3]: Receive Data Framing Error Flag
Logic 0 = No framing error (default).
Logic 1 = Framing error. The receive character did not have a valid stop bit(s). This error is associated with
the character available for reading in RHR.
LSR[4]: Receive Break Flag
Logic 0 = No break condition (default).
Logic 1 = The receiver received a break signal (RX was LOW for at least one character frame time). In the
FIFO mode, only one break character is loaded into the FIFO.
LSR[5]: Transmit Holding Register Empty Flag
This bit is the Transmit Holding Register Empty indicator. The THR bit is set to a logic 1 when the last data byte
is transferred from the transmit holding register to the transmit shift register. The bit is reset to logic 0
concurrently with the data loading to the transmit holding register by the host. In the FIFO mode this bit is set
when the transmit FIFO is empty, it is cleared when the transmit FIFO contains at least 1 byte.
相關PDF資料 |
PDF描述 |
|---|---|
| XR16L2751CM-F | IC UART FIFO 64B DUAL 48TQFP |
| MAX7311AAG+ | IC I/O EXPANDER I2C 16B 24SSOP |
| XR16C850IM-F | IC UART FIFO 128B 48TQFP |
| MAX7311ATG+T | IC I/O EXPANDER I2C 16B 24TQFN |
| XR16L2551IL-F | IC UART FIFO 16B DUAL 32QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16L2751IMTR-F | 制造商:Exar Corporation 功能描述:UART 2-CH 64Byte FIFO 2.5V/3.3V/5V 48-Pin TQFP T/R 制造商:Exar Corporation 功能描述:XR16L2751IMTR-F |
| XR16L2752 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 5.5V DUART WITH 64-BYTE FIFO |
| XR16L2752CJ | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 5.5V DUART WITH 64-BYTE FIFO |
| XR16L2752CJ-0A-EB | 功能描述:UART 接口集成電路 Supports L2750 44 ld PLCC, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L2752CJ-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。