參數資料
型號： XR16C854DCV-F
廠商： Exar Corporation
文件頁數： 22/53頁
文件大?。?/td> 0K
描述： IC UART FIFO 128B QUAD 64LQFP
標準包裝： 160
特點： *
通道數： 4，QUART
FIFO's： 128 字節
規程： RS232，RS485
電源電壓： 2.97 V ~ 5.5 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 64-LQFP
供應商設備封裝： 64-LQFP（10x10）
包裝： 托盤
XR16C854/854D
29
REV. 3.1.0
2.97V TO 5.5V QUAD UART WITH 128-BYTE FIFO
4.5
FIFO Control Register (FCR) - Write-Only
This register is used to enable the FIFOs, clear the FIFOs, set the transmit/receive FIFO trigger levels, and
select the DMA mode. The DMA and FIFO modes are defined as follows:
FCR[0]: TX and RX FIFO Enable
Logic 0 = Disable the transmit and receive FIFO (default).
Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to logic 1 when other FCR bits are
written or they will not be programmed.
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No receive FIFO reset (default)
Logic 1 = Reset the receive FIFO pointers and FIFO level counter logic (the receive shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No transmit FIFO reset (default).
Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[3]: DMA Mode Select
Controls the behavior of the TXRDY# and RXRDY# pins. See DMA operation section for details.
Logic 0 = Normal Operation (default).
Logic 1 = DMA Mode.
FCR[5:4]: Transmit FIFO Trigger Select
(logic 0 = default, TX trigger level = one)
These 2 bits set the trigger level for the transmit FIFO. The UART will issue a transmit interrupt when the
number of characters in the FIFO falls below the selected trigger level, or when it gets empty in case that the
FIFO did not get filled over the trigger level on last re-load. Table 11 below shows the selections. EFR bit-4
must be set to ‘1’ before these bits can be accessed. Note that the receiver and the transmitter cannot use
different trigger tables. Whichever selection is made last applies to both the RX and TX side.
FCR[7:6]: Receive FIFO Trigger Select
(logic 0 = default, RX trigger level =1)
The FCTR Bits 5-4 are associated with these 2 bits. These 2 bits are used to set the trigger level for the receive
FIFO. The UART will issue a receive interrupt when the number of the characters in the FIFO crosses the
trigger level. Table 11 shows the complete selections. Note that the receiver and the transmitter cannot use
different trigger tables. Whichever selection is made last applies to both the RX and TX side.
相關PDF資料
PDF描述
XR16C854IQTR-F IC UART FIFO 128B QUAD 100QFP
ATUC64D3-A2UR IC MCU 32BIT 64KB FLASH 64TQFP
ST16C654CQ100-F IC UART FIFO 64B QUAD 100QFP
XR16C854IJTR-F IC UART FIFO 128B QUAD 68PLCC
XR17D152IM-F IC UART PCI BUS DUAL 100TQFP
相關代理商/技術參數
參數描述
XR16C854DCVTR-F 制造商:Exar Corporation 功能描述:UART 4-CH 128Byte FIFO 3.3V/5V 64-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR16C854DCVTR-F
XR16C854DIV 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V QUAD UART WITH 128-BYTE FIFO
XR16C854DIV-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16C854DIV-F 制造商:Exar Corporation 功能描述:IC QUAD UART 2MBPS 5.5V 64-LQFP
XR16C854DIVTR-F 制造商:Exar Corporation 功能描述:UART 4-CH 128Byte FIFO 3.3V/5V 64-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR16C854DIVTR-F
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*