- 您現在的位置：買賣IC網 > Datasheet目錄58 > XIB-R (Digi International/Maxstream)BOARD INTERFACE RS232/485 Datasheet資料下載
參數資料
| 型號： | XIB-R |
| 廠商： | Digi International/Maxstream |
| 文件頁數： | 20/36頁 |
| 文件大?。?/td> | 826K |
| 描述： | BOARD INTERFACE RS232/485 |
| 標準包裝： | 1 |
| 附件類型： | 接口板 |
| 適用于相關產品： | XStream 和 Xcite 收音機 |
| 其它名稱： | Q2231853 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
9XCite"燨EM燫F燤odule?燩roduct燤anual爒2.1燵2007.01.04]
2007燤axStream,營nc.
牋牋?0
3.5. Command Descriptions
Commands and parameters are listed alphabetically. Parameter types and categories are desig-
nated between "< >" symbols. For example: . "AT Command" is the
command/parameter type and "Networking" is the command/parameter category.
AT (Guard Time After) Parameter
<Non-AT Settable Parameter: AT Command Options> AT Parameter is used to set the DI pin silent
time that follows the command sequence character (CC Parameter). By default, 1 half of a second
(500 milliseconds) must elapse before entering another character. The AT Command Mode
Sequence used to enter AT Command Mode is as follows:
"No characters sent for 1 millisecond [BT (Guard Time Before) Parameter]
"Send three plus characters "+++" [CC (Command Sequence Character) Parameter]
"No characters sent for 1 millisecond [AT (Guard Time After) Parameter]
All of the values in this sequence can be adjusted. AT Parameter is used to adjust the period of
silence that follows the command sequence character.
Parameter Range: 0x02 - 0xFFFF (x 1 millisecond)
# of bytes returned: 2
Default Parameter Value: 0x1F4 (500 decimal)
Related Commands: BT (Guard Time Before), CC (Commands Sequence Character)
BD (Interface Data Rate) Parameter
<Non-AT Settable Parameter: Serial Interfacing>
BD Parameter allows the user to adjust the UART
baud rate and thus modify the rate at which serial
data is sent to the modem. Baud rates range from
1200 to 57600 baud (bps). The new baud rate
does not take effect until CN (Exit AT Command
Mode) Command is issued.
Note: If the serial data baud rate is set to exceed
the fixed RF data baud rate of the XCite radio
modem, flow control may need to be imple-
mented.
BI (Number of Bits) Parameter
<Non-AT Settable Parameter: Serial Interfacing>
BI Parameter allows the user to define the num-
ber of data bits between the start and stop bits.
Setting 7 bits and Mark or Space parity (NB
Parameter) will result in a setting of 7 bits and no
parity.
Parameter Ranges: 0 - 6
Parameter
Configuration (bps)
0
1200
1
2400
2
4800
3
9600
4
19200
5
38400
6
57600
Default Parameter Value: Set to equal radio
modem's fixed RF data rate (baud)
Number of bytes returned: 1
Parameter Ranges: 0 - 1
Parameter
Configuration
0
7 bits
1
8 bits
Default Parameter Value: 1
Number of bytes returned: 1
相關PDF資料 |
PDF描述 |
|---|---|
| ZMN2400HPDB | BOARD ROUTER DEV ZIGBEE 100MW |
| ZMN24HPDK-B | KIT DEV W/ZIGBEE ZMN2400HP |
| ZNI1000TC | IC TEMP SENSOR NI1000 SOT23-3 |
| 02110102-000 | SNSR TILT RATIO 60DEG 500MA FLNG |
| 1-5209285-2 | FOPC BOA 12DB FC/UPC BP SM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XIB-U | 功能描述:界面模塊 USB interface board 24XStream 9XCite RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
| XIC25040 | 制造商:XIC 功能描述:25040 24HR '6 |
| XILINXPWR-079 | 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| XILINXPWR-080 | 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| XILINXPWR-081 | 功能描述:電源管理IC開發工具 Pwr Mgmt Eval Mod Xilinx RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。