參數資料
型號： XC2S600E-6FGG456C
廠商： Xilinx Inc
文件頁數： 24/108頁
文件大?。?/td> 0K
描述： IC SPARTAN-IIE FPGA 600K 456FBGA
產品變化通告： FPGA Family Discontinuation 18/Apr/2011
標準包裝： 60
系列： Spartan®-IIE
LAB/CLB數： 3456
邏輯元件/單元數： 15552
RAM 位總計： 294912
輸入/輸出數： 329
門數： 600000
電源電壓： 1.71 V ~ 1.89 V
安裝類型： 表面貼裝
工作溫度： 0°C ~ 85°C
封裝/外殼： 456-BBGA
供應商設備封裝： 456-FBGA
其它名稱： 122-1332
22
DS077-2 (v3.0) August 9, 2013
Product Specification
Spartan-IIE FPGA Family: Functional Description
R
— OBSOLETE — OBSOLETE — OBSOLETE — OBSOLETE —
Signals
There are two kinds of pins that are used to configure
Spartan-IIE devices: Dedicated pins perform only specific
configuration-related functions; the other pins can serve as
general purpose I/Os once user operation has begun.
The dedicated pins comprise the mode pins (M2, M1, M0),
the configuration clock pin (CCLK), the PROGRAM pin, the
DONE pin and the boundary-scan pins (TDI, TDO, TMS,
TCK). Depending on the selected configuration mode,
CCLK may be an output generated by the FPGA, or may be
generated externally, and provided to the FPGA as an input.
Note that some configuration pins can act as outputs. For
correct operation, these pins require a VCCO of 3.3V to drive
an LVTTL signal or 2.5V to drive an LVCMOS signal. All the
relevant pins fall in banks 2 or 3. The CS and WRITE pins
for Slave Parallel mode are located in bank 1.
For a more detailed description than that given below, see
Module 1 and XAPP176, Configuration and Readback of
the Spartan-II and Spartan-IIE FPGA Families.
The Process
The sequence of steps necessary to configure Spartan-IIE
devices are shown in Figure 16. The overall flow can be
divided into three different phases.
Initiating configuration
Configuration memory clear
Loading data frames
Start-up
The memory clearing and start-up phases are the same for
all configuration modes; however, the steps for the loading
of data frames are different. Thus, the details for data frame
loading are described separately in the sections devoted to
each mode.
Initiating Configuration
There are two different ways to initiate the configuration pro-
cess: applying power to the device or asserting the PRO-
GRAM input.
Configuration on power-up occurs automatically unless it is
delayed by the user, as described in a separate section
below. The waveform for configuration on power-up is
Before configuration can begin, VCCO Bank 2 must be
greater than 1.0V. Furthermore, all VCCINT power pins must
be connected to a 1.8V supply. For more information on
delaying configuration, see Clearing Configuration Memory,
Once in user operation, the device can be re-configured
simply by pulling the PROGRAM pin Low. The device
acknowledges the beginning of the configuration process by
driving DONE Low, then enters the memory-clearing phase.
Table 11: Configuration Modes
Configuration Mode
Preconfiguration
Pull-ups
M0
M1
M2
CCLK
Direction
Data Width
Serial DOUT
Master Serial mode
No
0
Out
1
Yes
0
1
Slave Parallel mode
(SelectMAP)
Yes
0
1
0
In
8
No
0
1
Boundary-Scan mode
Yes
1
0
N/A
1
No
1
0
1
Slave Serial mode
Yes
1
0
In
1
Yes
No
1
Notes:
1.
During power-on and throughout configuration, the I/O drivers will be in a high-impedance state. After configuration, all unused I/Os
(those not assigned signals) will remain in a high-impedance state. Pins used as outputs may pulse High at the end of configuration
2.
If the Mode pins are set for preconfiguration pull-ups, those resistors go into effect once the rising edge of INIT samples the Mode
pins. They will stay in effect until GTS is released during startup, after which the UnusedPin bitstream generator option will determine
whether the unused I/Os have a pull-up, pull-down, or no resistor.
相關PDF資料
PDF描述
25LC128T-E/ST IC EEPROM 128KBIT 10MHZ 8TSSOP
XCV100E-7BG352I IC FPGA 1.8V I-TEMP 352-MBGA
25LC128XT-E/ST IC EEPROM 128KBIT 10MHZ 8TSSOP
3342-4 JACK SCREW KIT, .35" LENGTH
3342-1 JACK SCREW KIT, .22" LENGTH
相關代理商/技術參數
參數描述
XC2S600E-6FGG456I 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-IIE FPGA
XC2S600E-6FGG676C 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-IIE FPGA
XC2S600E-6FGG676C4022 制造商:Xilinx 功能描述:
XC2S600E-6FGG676I 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-IIE FPGA
XC2S600E-6FT256C 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-IIE FPGA
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*