參數資料
型號: XC2S30-5VQ100I
廠商: Xilinx Inc
文件頁數: 13/99頁
文件大?。?/td> 0K
描述: IC FPGA 2.5V I-TEMP 100-VQFP
標準包裝: 90
系列: Spartan®-II
LAB/CLB數: 216
邏輯元件/單元數: 972
RAM 位總計: 24576
輸入/輸出數: 60
門數: 30000
電源電壓: 2.375 V ~ 2.625 V
安裝類型: 表面貼裝
工作溫度: -40°C ~ 100°C
封裝/外殼: 100-TQFP
供應商設備封裝: 100-VQFP(14x14)
Spartan-II FPGA Family: Functional Description
DS001-2 (v2.8) June 13, 2008
Module 2 of 4
Product Specification
20
R
By default, these operations are synchronized to CCLK.
The entire start-up sequence lasts eight cycles, called
C0-C7, after which the loaded design is fully functional. The
default timing for start-up is shown in the top half of
Figure 13. The four operations can be selected to switch on
any CCLK cycle C1-C6 through settings in the Xilinx
software. Heavy lines show default settings.
The bottom half of Figure 13 shows another commonly
used version of the start-up timing known as
Sync-to-DONE. This version makes the GTS, GSR, and
GWE events conditional upon the DONE pin going High.
This timing is important for a daisy chain of multiple FPGAs
in serial mode, since it ensures that all FPGAs go through
start-up together, after all their DONE pins have gone High.
Sync-to-DONE timing is selected by setting the GTS, GSR,
and GWE cycles to a value of DONE in the configuration
options. This causes these signals to transition one clock
cycle after DONE externally transitions High.
Serial Modes
There are two serial configuration modes: In Master Serial
mode, the FPGA controls the configuration process by
driving CCLK as an output. In Slave Serial mode, the FPGA
passively receives CCLK as an input from an external agent
(e.g., a microprocessor, CPLD, or second FPGA in master
mode) that is controlling the configuration process. In both
modes, the FPGA is configured by loading one bit per
CCLK cycle. The MSB of each configuration data byte is
always written to the DIN pin first.
See Figure 14 for the sequence for loading data into the
Spartan-II FPGA serially. This is an expansion of the "Load
Configuration Data Frames" block in Figure 11. Note that
CS and WRITE normally are not used during serial
configuration. To ensure successful loading of the FPGA,
do not toggle WRITE with CS Low during serial
configuration.
Figure 13: Start-Up Waveforms
Start-up CLK
Default Cycles
Sync to DONE
01
2
3
4
5
6
7
01
DONE High
23
4
56
7
Phase
Start-up CLK
Phase
DONE
GTS
GSR
GWE
DS001_13_090600
DONE
GTS
GSR
GWE
Figure 14: Loading Serial Mode Configuration Data
DS001_14_042403
No
Yes
End of
Configuration
Data File?
After INIT
Goes High
User Load One
Configuration
Bit on Next
CCLK Rising Edge
To CRC Check
相關PDF資料
PDF描述
AMM25DTMS CONN EDGECARD 50POS R/A .156 SLD
XC2S30-5TQG144C IC SPARTAN-II FPGA 30K 144-TQFP
ASM44DSEF-S13 CONN EDGECARD 88POS .156 EXTEND
AMM44DSEF-S13 CONN EDGECARD 88POS .156 EXTEND
ASM44DRTF-S13 CONN EDGECARD 88POS .156 EXTEND
相關代理商/技術參數
參數描述
XC2S30-5VQG100C 功能描述:IC FPGA 2.5V 216 CLB'S 100-VQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:Spartan®-II 標準包裝:60 系列:XP LAB/CLB數:- 邏輯元件/單元數:10000 RAM 位總計:221184 輸入/輸出數:244 門數:- 電源電壓:1.71 V ~ 3.465 V 安裝類型:表面貼裝 工作溫度:0°C ~ 85°C 封裝/外殼:388-BBGA 供應商設備封裝:388-FPBGA(23x23) 其它名稱:220-1241
XC2S30-5VQG100I 制造商:Xilinx 功能描述:FPGA SPARTAN-II 30K GATES 972 CELLS 263MHZ 2.5V 100VTQFP - Trays 制造商:Xilinx 功能描述:IC SYSTEM GATE
XC2S30-6CS144C 功能描述:IC FPGA 2.5V C-TEMP 144-CSBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:Spartan®-II 標準包裝:40 系列:Spartan® 6 LX LAB/CLB數:3411 邏輯元件/單元數:43661 RAM 位總計:2138112 輸入/輸出數:358 門數:- 電源電壓:1.14 V ~ 1.26 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 100°C 封裝/外殼:676-BGA 供應商設備封裝:676-FBGA(27x27)
XC2S30-6CS144I 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-II 2.5V FPGA Family:Introduction and Ordering Information
XC2S30-6CSG144C 制造商:Xilinx 功能描述:FPGA SPARTAN-II 30K GATES 972 CELLS 263MHZ 2.5V 144CSBGA - Trays