SERIAL D
參數資料
型號： X9268UV24
廠商： Intersil
文件頁數： 18/22頁
文件大?。?/td> 0K
描述： IC XDCP DUAL 256TAP 50K 24-TSSOP
標準包裝： 62
系列： XDCP™
接片： 256
電阻（歐姆）： 50k
電路數： 2
溫度系數： 標準值 ±300 ppm/°C
存儲器類型： 非易失
接口： I²C（設備位址）
電源電壓： 4.5 V ~ 5.5 V
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 24-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 24-TSSOP
包裝： 管件
5
FN8172.4
August 29, 2006
PIN DESCRIPTIONS
Bus Interface Pins
SERIAL DATA INPUT/OUTPUT (SDA)
The SDA is a bidirectional serial data input/output pin
for a 2-Wire slave device and is used to transfer data
into and out of the device. It receives device address,
opcode, wiper register address and data sent from an
2-Wire master at the rising edge of the serial clock
SCL, and it shifts out data after each falling edge of
the serial clock SCL.
It is an open drain output and may be wire-ORed with
any number of open drain or open collector outputs.
An open drain output requires the use of a pull-up
resistor. For selecting typical values, refer to the
guidelines for calculating typical values on the bus
pull-up resistors graph.
SERIAL CLOCK (SCL)
This input is used by 2-Wire master to supply 2-Wire
serial clock to the X9268.
DEVICE ADDRESS (A3 - A0)
The address inputs are used to set the least significant
3 bits of the 8-bit slave address. A match in the slave
address serial data stream must be made with the
Address input in order to initiate communication with
the X9268. A maximum of 8 devices may occupy the
2-Wire serial bus.
Potentiometer Pins
RH, RL
The RH and RL pins are equivalent to the terminal
connections on a mechanical potentiometer. Since
there are 2 potentiometers, there are 2 sets of RH and
RL such that RH0 and RL0 are the terminals of POT 0
and so on.
RW
The wiper pin are equivalent to the wiper terminal of a
mechanical
potentiometer.
Since
there
are
4
potentiometers, there are 2 sets of RW such that RW0
is the terminal of POT 0 and so on.
Bias Supply Pins
SYSTEM SUPPLY VOLTAGE (VCC) AND SUPPLY
GROUND (VSS)
The VCC pin is the system supply voltage. The VSS
pin is the system ground.
Analog Supply Voltages (V+ and V
-)
These supplies are the analog voltage supplies for the
potentiometer. The V+ supply is tied to the wiper
switches while the V- supply is used to bias the
switches and the internal P+ substrate of the
integrated circuit. Both of these supplies set the
voltage limits of the potentiometer.
Other Pins
NO CONNECT
No connect pins should be left open. This pins are
used for Intersil manufacturing and testing purposes.
HARDWARE WRITE PROTECT INPUT (WP)
The WP pin when LOW prevents nonvolatile writes to
the Data Registers.
X9268
相關PDF資料
PDF描述
X9269UV24IZ-2.7T1 IC XDCP DUAL 256TAP 50K 24-TSSOP
X9271UV14T1 IC XDCP SGL 256TAP 50K 14-TSSOP
X9279UV14ZT1 IC XDCP SGL 256TAP 50K 14-TSSOP
X9313ZST2 IC XDCP 32-TAP 1K 3-WIRE 8-SOIC
X9314WST2 IC XDCP SGL 32-TAP 10K 8-SOIC
相關代理商/技術參數
參數描述
X9269 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual Digitally-Controlled Potentiometers
X9269_07 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual Digitally-Controlled Potentiometers
X9269TB16 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Dual Digitally-Controlled Potentiometers
X9269TB16-2.7 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Dual Digitally-Controlled Potentiometers
X9269TB16I 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Dual Digitally-Controlled Potentiometers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*