- 您現在的位置：買賣IC網 > PDF目錄9139 > X9252YV24I-2.7 (Intersil)IC DCP QUAD 2.8K 256TAP 24-TSSOP PDF資料下載
參數資料
| 型號： | X9252YV24I-2.7 |
| 廠商： | Intersil |
| 文件頁數： | 6/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DCP QUAD 2.8K 256TAP 24-TSSOP |
| 標準包裝： | 62 |
| 系列： | XDCP™ |
| 接片： | 256 |
| 電阻（歐姆）： | 2.8k |
| 電路數： | 4 |
| 溫度系數： | 標準值 ±300 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | I²C（芯片選擇，設備位址，增/減） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 24-TSSOP |
| 包裝： | 管件 |
14
FN8167.2
November 14, 2005
Page Write Operation
As stated previously, the memory is organized as a single
Status Register (SR), and four pages of four registers each.
Each page contains one Data Register for each DCP. The
order of the bytes within a page is DR0i, followed by DR1i,
followed by DR2i, and then DR3i, with i being the Data
Register number (0, 1, 2, or 3). Normally a page write
operation will be used to efficiently update all four data
registers and WCR in a single write command, starting at
DCP0 and finishing with DCP3.
In order to perform a Page Write operation to the memory
array, the NVEnable bit in the SR must first be set to “1”.
A Page Write operation is initiated in the same manner as
the byte write operation; but instead of terminating the write
cycle after the first data byte is transferred, the master can
transmit up to 4 bytes (See Figure 8). After the receipt of
each byte, the X9252 responds with an ACK, and the
internal DCP address counter is incremented by one. The
page address remains constant. When the counter reaches
the end of the page (DR3i, 03hex), it “rolls over” and goes
back to the first byte of the same page (DR0i, 00hex).
For example, if the master writes 3 bytes to a page starting
at location DR22, the first 2 bytes are written to locations
DR22 and DR32, while the last byte is written to locations
DR02. Afterwards, the DCP counter would point to location
DR12. If the master supplies more than 4 bytes of data, then
new data overwrites the previous data, one byte at a time.
The master terminates the loading of Data Bytes by issuing
a STOP condition, which initiates the nonvolatile write cycle.
As with the Byte Write operation, all inputs are disabled until
completion of the internal write cycle. If the WP pin is low,
the nonvolatile write cycle doesn’t start and the bytes are
discarded.
Notice that the Data Bytes are also written to the WCR of the
corresponding DCPs, therefore in the above example,
WCR2, WCR3, and WCR0 are also written and WCR1 is
updated with the contents of DR12.
2 < n < 4
Signals from the
Master
Signals from the
Slave
Signal at SDA
S
t
a
r
t
Slave
Address
Byte
A
C
K
A
C
K
0
11
Data Byte (1)
S
t
o
p
A
C
K
A
C
K
Data Byte (n)
Write
FIGURE 8. PAGE WRITE OPERATION
X9252
相關PDF資料 |
PDF描述 |
|---|---|
| CD74HC4046APWTG4 | IC PLL W/VCO 16-SSOP |
| CD74HCT4046AMTE4 | IC PLL W/VCO HS 16-SOIC |
| CD74HCT4046AMT | IC PLL W/VCO HS 16-SOIC |
| V375B28H300BF2 | CONVERTER MOD DC/DC 28V 300W |
| CD74HC4046APWTE4 | IC PLL W/VCO 16-SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9252YV24IZ-2.7 | 功能描述:IC POT DGTL QUAD 24-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP（3x3） 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT |
| X9258 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Noise/Low Power/2-Wire Bus/256 Taps |
| X9258)06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad Digital Controlled Potentiometers |
| X9258_11 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad Digital Controlled Potentiometers(XDCP?) |
| X9258_13 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Noise/Low Power/2-Wire Bus/256 Taps |
發布緊急采購，3分鐘左右您將得到回復。