- 您現在的位置：買賣IC網 > PDF目錄9413 > X9111TV14IZ-2.7 (Intersil)IC XDCP SGL 1024TAP 100K 14TSSOP PDF資料下載
參數資料
| 型號： | X9111TV14IZ-2.7 |
| 廠商： | Intersil |
| 文件頁數： | 14/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC XDCP SGL 1024TAP 100K 14TSSOP |
| 標準包裝： | 95 |
| 系列： | XDCP™ |
| 接片： | 1024 |
| 電阻（歐姆）： | 100k |
| 電路數： | 1 |
| 溫度系數： | 標準值 ±300 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | 6 線 SPI（芯片選擇，設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 14-TSSOP |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁
6
FN8159.4
September 15, 2006
Five of the seven instructions are four bytes in length. These
instructions are:
Read Wiper Counter Register – read the current wiper
position of the selected pot,
Write Wiper Counter Register – change current wiper
position of the selected pot,
Read Data Register – read the contents of the selected
data register;
Write Data Register – write a new value to the selected
data register.
Read Status – This command returns the contents of the
WIP bit which indicates if the internal write cycle is in
progress.
The basic sequence of the four byte instructions is illustrated
in Figure 3. These four-byte instructions exchange data
between the WCR and one of the Data Registers. A transfer
from a Data Register to a WCR is essentially a write to a
static RAM, with the static RAM controlling the wiper
position. The response of the wiper to this action will be
delayed by tWRL. A transfer from the WCR (current wiper
position), to a Data Register is a write to nonvolatile memory
and takes a minimum of tWR to complete. The transfer can
occur between the potentiometer and one of its associated
registers. The Read Status Register instruction is the only
unique format (see Figure 4).
Two instructions require a two-byte sequence to complete
(see Figure 2). These instructions transfer data between the
host and the X9111; either between the host and one of the
Data Registers or directly between the host and the Wiper
Counter Register. These instructions are:
XFR Data Register to Wiper Counter Register –This
transfers the contents of one specified Data Register to
the associated Wiper Counter Register.
XFR Wiper Counter Register to Data Register – This
transfers the contents of the specified Wiper Counter
Register to the specified associated Data Register.
See Instruction format for more details.
Write in Process (WIP bit)
The contents of the Data Registers are saved to nonvolatile
memory when the CS pin goes from LOW to HIGH after a
complete write sequence is received by the device. The
progress of this internal write operation can be monitored by
a Write In Process bit (WIP). The WIP bit is read with a Read
Status command (see Figure 4).
Power Up and Down Requirements
There are no restrictions on the power-up condition of VCC
and the voltages applied to the potentiometer pins provided
that the VCC is always more positive than or equal to the
voltages at RH, RL, and RW, i.e., VCC ≥ RH, RL, RW. There
are no restrictions on the power-down condition. However,
the datasheet parameters for the DCP do not apply until
1millisecond after VCC reaches its final value.
ID3
ID2
ID1
ID0
0
A1
A0
I2
I1
I0
RB
RA
SCK
SI
CS
0101
R/W
Device ID
Internal
Instruction
Opcode
Address
Register
0
Address
0
FIGURE 2. TWO-BYTE INSTRUCTION SEQUENCE
ID3 ID2 ID1 ID0 0
A0 R/W I2
00
SCK
SI
0
X
X0
0
XX
X
W
C
R
9
W
C
R
8
W
C
R
7
W
C
R
6
W
C
R
5
W
C
R
4
W
C
R
3
W
C
R
2
W
C
R
1
W
C
R
0
CS
I1
0
101
0
XX
X
Device ID
Internal
Address
Instruction
Opcode
Register
Address
Wiper
Position
A1
FIGURE 3. FOUR-BYTE INSTRUCTION SEQUENCE (WRITE OR READ FOR WCR OR DATA REGISTERS)
X9111
相關PDF資料 |
PDF描述 |
|---|---|
| DS2417P+ | IC TIMECHIP W/INTRPT 1WIRE 6TSOC |
| DS1344E-18+T&R | IC RTC SPI 1.8V 20TSSOP |
| VI-22K-MX-B1 | CONVERTER MOD DC/DC 40V 75W |
| VI-22K-MW | CONVERTER MOD DC/DC 40V 100W |
| VI-22J-MX-B1 | CONVERTER MOD DC/DC 36V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9111TV14Z | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9111TV14Z-2.7 | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9116 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Digitally Controlled Potentiometer |
| X9116_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Digitally Controlled Potentiometer |
| X9116_11 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Digitally Controlled Potentiometer |
發布緊急采購，3分鐘左右您將得到回復。