- 您現(xiàn)在的位置：買賣IC網 > PDF目錄376445 > X9015WS8ZT1 (INTERSIL CORP) Single Digitally Controlled Potentiometer PDF資料下載
參數資料
| 型號： | X9015WS8ZT1 |
| 廠商： | INTERSIL CORP |
| 元件分類： | 數字電位計 |
| 英文描述： | Single Digitally Controlled Potentiometer |
| 中文描述： | 10K DIGITAL POTENTIOMETER, INCREMENT/DECREMENT CONTROL INTERFACE, 32 POSITIONS, PDSO8 |
| 封裝： | ROHS COMPLIANT, PLASTIC, MS-012AA, SOIC-8 |
| 文件頁數： | 3/11頁 |
| 文件大小： | 252K |
| 代理商： | X9015WS8ZT1 |
3
FN8157.5
August 31, 2006
Pin Descriptions
R
H
/V
H
and R
L
/V
L
The high (R
H
/V
H
) and low (R
L
/V
L
) terminals of the X9015 are
equivalent to the fixed terminals of a mechanical
potentiometer. The minimum voltage is V
SS
and the
maximum is V
CC
. The terminology of R
L
/V
L
and R
H
/V
H
references the relative position of the terminal in relation to
wiper movement direction selected by the U/D input, and not
the voltage potential on the terminal.
R
W
/V
W
R
W
/V
w
is the wiper terminal and is equivalent to the movable
terminal of a mechanical potentiometer. The position of the
wiper within the array is determined by the control inputs.
The wiper terminal series resistance is typically 200
Ω
at
V
CC
=5V. At power up the wiper position is at Tap #15.
(V
L
/R
L
=Tap #0).
Up/Down (U/D)
The U/D input controls the direction of the wiper movement
and whether the tap position is incremented or decremented.
Increment (INC)
The INC input is negative-edge triggered. Toggling INC will
move the wiper and either increment or decrement the
counter in the direction indicated by the logic level on the U/D
input.
Chip Select (CS)
The device is selected when the CS input is LOW. When CS
is returned HIGH while the INC input is also HIGH the X9015
will be placed in the low power standby mode until the device
is selected once again.
Principles Of Operation
There are two sections of the X9015: the input control,
counter and decode section; and the resistor array. The input
control section operates just like an up/down counter. The
output of this counter is decoded to turn on a single electronic
switch connecting a point on the resistor array to the wiper
output. The resistor array is comprised of 31 individual
resistors connected in series.
The wiper, when at either fixed terminal, acts like its
mechanical equivalent and does not move beyond the last
position. That is, the counter does not wrap around when
clocked to either extreme.
The electronic switches on the device operate in a “make
before break” mode when the wiper changes tap positions. If
the wiper is moved several positions, multiple taps are
connected to the wiper for t
IW
(INC to V
W
change). The
R
TOTAL
value for the device can temporarily be reduced by a
significant amount if the wiper is moved several positions.
When the device is powered-down, the wiper position is lost.
When power is restored, the wiper is set to Tap #15.
Instructions and Programming
The INC, U/D and CS inputs control the movement of the
wiper along the resistor array. With CS set LOW the device is
selected and enabled to respond to the U/D and INC inputs.
HIGH to LOW transitions on INC will increment or decrement
(depending on the state of the U/D input) a five bit counter.
The output of this counter is decoded to select one of thirty
two wiper positions along the resistive array.
The system may select the X9015, move the wiper and
deselect the device. The new wiper position will be maintained
until changed by the system or until a power-up/down cycle.
The state of U/D may be changed while CS remains LOW.
This allows the host system to enable the device and then
move the wiper up and down until the proper trim is attained.
Pin Names
SYMBOL
DESCRIPTION
RH/VH
High terminal
RW/VW
Wiper terminal
RL/VL
Low terminal
VSS
Ground
VCC
Supply voltage
U/D
Up/Down control input
INC
Increment control input
CS
Chip select control input
Mode Selection
CS
INC
U/D
MODE
L
H
Wiper up
L
L
Wiper down
H
X
Standby mode
H
X
X
Standby mode
L
L
X
Normal mode
L
H
Wiper Up (not recommended)
L
L
Wiper Down (not recommend-
ed)
X9015
相關PDF資料 |
PDF描述 |
|---|---|
| X9111TV14IZ | Single Digitally-Controlled (XDCP⑩) Potentiometer |
| X9111TV14IZ-2.7 | Single Digitally-Controlled (XDCP⑩) Potentiometer |
| X9111TV14Z | Single Digitally-Controlled (XDCP⑩) Potentiometer |
| X9111TV14Z-2.7 | Single Digitally-Controlled (XDCP⑩) Potentiometer |
| X9116WM8T1 | Digitally Controlled Potentiometer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X90840 WAF | 制造商:Intersil Corporation 功能描述: |
| X90A104K | 制造商: 功能描述: 制造商:MEPCO/CENTRALAB A NORTH A 功能描述: 制造商:undefined 功能描述: |
| X9110 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Single Digitally-Controlled (XDCP) Potentiometer |
| X9110_08 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual Supply/Low Power/1024-Tap/SPI Bus |
| X9110TV14 | 功能描述:IC DCP 100K 1024TP 14TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
發(fā)布緊急采購，3分鐘左右您將得到回復。