- 您現在的位置：買賣IC網 > PDF目錄374960 > X80120 (Intersil Corporation) Voltage Supervisor/Sequencer Dual Programmable Time Delay with Local/Remote Voltage Monitors PDF資料下載
參數資料
| 型號： | X80120 |
| 廠商： | Intersil Corporation |
| 英文描述： | Voltage Supervisor/Sequencer Dual Programmable Time Delay with Local/Remote Voltage Monitors |
| 中文描述： | 電壓監控/雙可編程序時滯與本地/遠程電壓監視器 |
| 文件頁數： | 8/17頁 |
| 文件大?。?/td> | 318K |
| 代理商： | X80120 |
8
FN8151.0
January 20, 2005
Functional Description
Power On Reset and System Reset With Delay
Application of power to the X80120 activates a Power On
Reset circuit that pulls the RESET pin active. This signal, if
used, prevents the system microprocessor from starting to
operate while there is insufficient voltage on any of the
supplies. This circuit also does the following:
It prevents the processor from operating prior to
stabilization of the oscillator.
It allows time for an FPGA to download its configuration
prior to initialization of the circuit.
It prevents communication to the EEPROM during
unstable power conditions, greatly reducing the likelihood
of data corruption on power up.
It allows time for all supplies to turn on and stabilize prior
to system initialization.
The POR/RESET circuit is activated when all voltages are
within specified ranges and the V1GDO and V4GDO time-
out conditions are met. The POR/RESET circuit will then
wait t
SPOR
and de-assert the RESET pin. The POR delay
may be changed by setting the TPOR bits in register CR2.
The delay can be set to 100ms, 500ms, 1 second, or 5
seconds.
Pin Descriptions
PIN
NAME
DESCRIPTION
1
V4GDO
V4 Voltage Good Delay Output (Active LOW).
This open drain output goes HIGH when V4MON is less than V
REF4
and goes LOW when V4MON is greater than V
REF4
. There is user selectable delay circuitry on this pin.
2
V4MON
V4 Voltage Monitor Input. Second voltage monitor pin. If unused connect to V
CC
.
3
DNC
Do Not Connect
4
V
CC
Connect to V
CC
.
5
DNC
Do Not Connect.
6
V
P
V
CC
EEPROM programming Voltage.
7
Connect to V
CC
.
8
DNC
Do Not Connect.
9
A1
Address Select Input. It has an internal pull-down resistor. (>10M
typical)
The A0 and A1 bits allow for up to 4 X80120 devices to be used on the same SMBus serial interface.
10
SDA
Serial Data.
SDA is a bidirectional pin used to transfer data into and out of the device. It has an open drain output and
may be wire ORed with other open drain or open collector outputs. This pin requires a pull up resistor and the input
buffer is always active (not gated).
11
SCL
Serial Clock.
The Serial Clock controls the serial bus timing for data input and output.
12
V1MON
V1 Voltage Monitor Input.
First voltage monitor pin. If unused connect to V
CC
.
13
V1GDO
V1 Voltage Good Delay Output (Active LOW).
This open drain output goes HIGH when V1MON is less than V
REF1
and goes LOW when V1MON is greater than V
REF1
. There is user selectable delay circuitry on this pin.
14
RESET
RESET Output.
This open drain pin is an active LOW output. This pin will be active until all ViGDO pins go inactive and
the power sequencing is complete. This pin will be released after a programmable delay.
15
WP
Write Protect. Input Pin.
WP HIGH (in conjunction with WPEN bit=1) prevents writes to any memory location in the
device. It has an internal pull-down resistor. (>10M
typical)
16
MR
Manual Reset.
Pulling the MR pin HIGH initiates a RESET. The MR signal must be held HIGH for 5
μ
secs. It has an
internal pull-down resistor. (>10M
typical)
17
V
SS
NC
Ground Input.
18
No Connect.
No internal connections.
19
A0
Address Select Input.
It has an internal pull-down resistor. (>10M
typical) The A0 and A1 bits allow for up to 4
X80120 devices to be used on the same SMBus serial interface.
20
V
CC
Supply Voltage.
TABLE 1. POR RESET DELAY OPTIONS
TPOR1
TPOR0
t
SPOR
DELAY BEFORE RESET
ASSERTION
0
0
100 miliseconds (default)
0
1
500 miliseconds
1
0
1 second
1
1
5 seconds
X80120, X80121
相關PDF資料 |
PDF描述 |
|---|---|
| X80121 | Voltage Supervisor/Sequencer Dual Programmable Time Delay with Local/Remote Voltage Monitors |
| X80131Q20I | Voltage Supervisor/Sequencer Triple Programmable Time Delay with Local/Remote Voltage Monitors |
| X80133Q20I | Voltage Supervisor/Sequencer Triple Programmable Time Delay with Local/Remote Voltage Monitors |
| X80133 | Voltage Supervisor/Sequencer Triple Programmable Time Delay with Local/Remote Voltage Monitors |
| X80134 | Voltage Supervisor/Sequencer Triple Programmable Time Delay with Local/Remote Voltage Monitors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X80120Q20I | 制造商:Intersil Corporation 功能描述:Voltage Supervisor/Sequencer Dual Programmable Time Delay with Local/Remote Voltage Monitors |
| X80121 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Voltage Supervisor/Sequencer Dual Programmable Time Delay with Local/Remote Voltage Monitors |
| X80121Q20I | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Voltage Supervisor/Sequencer Dual Programmable Time Delay with Local/Remote Voltage Monitors |
| X80130 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Voltage Supervisor/Sequencer Triple Programmable Time Delay with Local/Remote Voltage Monitors |
| X80130Q20I | 制造商:Intersil Corporation 功能描述:Voltage Supervisor/Sequencer Triple Programmable Time Delay with Local/Remote Voltage Monitors |
發布緊急采購，3分鐘左右您將得到回復。