- 您現在的位置：買賣IC網 > PDF目錄10775 > X79000V20IT1 (Intersil)IC DAC NV SELECT OUT/MEM 20TSSOP PDF資料下載
參數資料
| 型號： | X79000V20IT1 |
| 廠商： | Intersil |
| 文件頁數： | 4/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC NV SELECT OUT/MEM 20TSSOP |
| 標準包裝： | 2,500 |
| 設置時間： | 6µs |
| 位數： | 12 |
| 數據接口： | 串行 |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 帶卷 (TR) |
| 輸出數目和類型： | 1 電壓，單極 |
| 采樣率（每秒）： | 417k |
12
FN8147.0
March 17, 2005
VOLTAGE REFERENCES
The device includes an on-chip bandgap reference
circuit with 1.21 V nominal output voltage. This voltage is
available at pin VRef as an output.
The voltages at pins VH and VL determine the DAC
output voltage at full scale and zero scale respectively.
Full scale is when the DAC input register is FFF hex (all
ones), and zero scale is when the DAC input register is
000 hex (all zeros).
V(VH) and V(VL) can be generated on-chip and can be
independently programmed to the values indicated in
table 1. VH must always be at a higher voltage than VL.
VH must not be higher than 3.1V. VL & VH can also be
independently disabled, in which case they become
inputs to the device.
SERIAL INTERFACE
Serial Interface Conventions
The device supports the SPI interface hardware protocol.
The protocol defines any device that sends data onto the
bus as a transmitter, and the receiving device as the
receiver. The device controlling the transfer is called the
master and the device being controlled is called the
slave. The master always initiates data transfers, and
provides the clock for both transmit and receive
operations. The X79000 operates as a slave in all
applications.
The device is accessed via the SI and SCK pins, while
the output data is presented at the SO pin. Input data at
pin SI is clocked-in on the rising edge of SCK, when CS
and RDY are both LOW. Output data at pin SO is
clocked-out on the falling edge of SCK.
All commands start with a falling edge at the input pin
CS. Write operations end with a rising edge at the input
pin CS after the last bit of the data bytes being written is
clocked-in. Read operations end with a rising edge at the
input pin CS after the last bit of the data byte being read
is clocked-out.
X79000 MEMORY MAP
The X79000 contains a 512-bit array of mixed volatile
and nonvolatile memory. The array is organized as 64
bytes, and it’s logically split up into two parts, namely:
– General Purpose Memory (GPM)
– Control and Status Registers
The GPM is all nonvolatile EEPROM, located at memory
addresses 00h to 37h.
Figure 2. X79000 Memory Map
The Control and Status registers of the X79000 are used
in the test and setup of the device in a system, and
include the DAC volatile register and the DAC nonvolatile
initial value register. These registers are realized as a
combination of both volatile and nonvolatile memory.
These registers reside in the memory locations 38h
through 3Fh. The reserved bits within registers 38h
through 3Dh must be written as “0” if writing to them, and
should be ignored when reading. The reserved registers,
3Ah, 3Bh, 3Eh and 3Fh, must not be written, and their
content should be ignored.
Factory control bit settings:
38h, 39h, 3Fh = All “0”s
3Ch = 1000 0100 (84 hex)
All communication to the X79000 over the SPI bus is
conducted by sending the MSB of each byte of data first.
The memory is physically realized as one contiguous
array, organized as 8 pages of 8 bytes each.
Bit 0
Bit 7
Address
Size
8 Bytes
56 Bytes
00h
37h
38h
3Fh
Control & Status
Registers
General Purpose
Memory (GPM)
...
X79000, X79001, X79002
相關PDF資料 |
PDF描述 |
|---|---|
| VE-J6B-MW-F1 | CONVERTER MOD DC/DC 95V 100W |
| B37931K9223K060 | CAP CER 0.022UF 16V 10% X7R 0603 |
| X79000V20I | IC DAC NV SELECT OUT/MEM 20TSSOP |
| VE-J63-MW-F3 | CONVERTER MOD DC/DC 24V 100W |
| ISL5961/2IA | IC DAC 14BIT 210MSPS 28-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X79001 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:NV DAC with Selectable Output Range and Memory |
| X79001V20I | 功能描述:IC DAC NV SELECT OUT/MEM 20TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率（每秒）:* |
| X79001V20IT1 | 功能描述:IC DAC NV SELECT OUT/MEM 20TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率（每秒）:* |
| X79002 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:NV DAC with Selectable Output Range and Memory |
| X79002V20I | 功能描述:IC DAC NV SELECT OUT/MEM 20TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率（每秒）:* |
發布緊急采購，3分鐘左右您將得到回復。