- 您現在的位置：買賣IC網 > PDF目錄385048 > X76F641XG (IC MICROSYSTEMS SDN BHD) 4 Mbit Uniform Sector, Serial Flash Memory PDF資料下載
參數資料
| 型號： | X76F641XG |
| 廠商： | IC MICROSYSTEMS SDN BHD |
| 元件分類： | DRAM |
| 英文描述： | 4 Mbit Uniform Sector, Serial Flash Memory |
| 中文描述： | 8K X 8 FLASH 5V PROM CARD, XMA8 |
| 封裝： | ROHS COMPLIANT, SMART CARD MODULE-8 |
| 文件頁數： | 3/17頁 |
| 文件大?。?/td> | 167K |
| 代理商： | X76F641XG |
X76F641
3
Figure 1. X76F641 Device Operation
Retry Counter
The X76F641 contains a retry counter. The retry counter
allows 8 accesses with an invalid password before any
action is taken. The counter will increment with any com-
bination of incorrect passwords. If the retry counter over-
flows, all memory areas are cleared and the device is
locked by preventing any read or write array password
matches. The passwords are unaffected. If a correct
password is received prior to retry counter overflow, the
retry counter is reset and access is granted. In order to
reset the operation of a locked up device, a special reset
command must be used with a RESET password.
Device Protocol
The X76F641 supports a bidirectional bus oriented proto-
col. The protocol defines any device that sends data onto
the bus as a transmitter and the receiving device as a
receiver. The device controlling the transfer is a master
and the device being controlled is the slave. The master will
always initiate data transfers and provide the clock for
both transmit and receive operations. Therefore, the
X76F641 will be considered a slave in all applications.
Clock and Data Conventions
Data states on the SDA line can change only during SCL
LOW. SDA changes during SCL HIGH are reserved for
indicating start and stop conditions. Refer to Figure 2 and
Figure 3.
Start Condition
All commands are preceded by the start condition,
which is a HIGH to LOW transition of SDA when SCL is
HIGH. The X76F641 continuously monitors the SDA and
SCL lines for the start condition and will not respond to
any command until this condition is met.
A start may be issued to terminate the input of a control
byte or the input data to be written. This will reset the
device and leave it ready to begin a new read or write
command. Because of the push/pull output, a start can-
not be generated while the part is outputting data. Starts are
inhibited while a write is in progress.
Stop Condition
All communications must be terminated by a stop condi-
tion. The stop condition is a LOW to HIGH transition of
SDA when SCL is HIGH. The stop condition is also used to
reset the device during a command or data input
sequence and will leave the device in the standby power
mode. As with starts, stops are inhibited when outputting
data and while a write is in progress.
Acknowledge
Acknowledge is a software convention used to indicate
successful data transfer. The transmitting device, either
master or slave, will release the bus after transmitting
eight bits. During the ninth clock cycle the receiver will
pull the SDA line LOW to acknowledge that it received the
eight bits of data.
The X76F641 will respond with an acknowledge after
recognition of a start condition and its slave address.
If
both the device and a write condition have been
selected, the X76F641 will respond with an acknowledge
after the receipt of each subsequent eight-bit word.
Reset Device Command
The reset device command is used to clear the retry
counter and reactivate the device. When the reset device
command is used prior to the retry counter overflow, the retry
counter is reset and no arrays or passwords are
affected. If the retry counter has overflowed, all memory
areas are cleared and all commands are blocked and the
retry counter is disabled. Issuing a valid reset device
command (with reset password) to the device resets and
re-enables the retry counter and re-enables the other
commands. Again, the passwords are not affected.
Reset Password Command
A reset password command will clear both arrays and set all
passwords to all zero.
LOAD COMMAND BYTE
LOAD 2 BYTE ADDRESS
LOAD 8-BYTE
PASSWORD
VERIFY PASSWORD
ACCEPTANCE BY
USE OF PASSWORD ACK POLLING
READ/WRITE
DATA BYTES
7025 FM 03
Twc OR DATA ACK POLLING
相關PDF資料 |
PDF描述 |
|---|---|
| X76F641XG-2.0 | 4 Mbit Uniform Sector, Serial Flash Memory |
| X84128 | Advanced MPS⑩ Micro Port Saver EEPROM with Block Lock⑩ Protection |
| X84640E-1.8 | Advanced MPS⑩ Micro Port Saver EEPROM with Block Lock⑩ Protection |
| X84640E-2.5 | Advanced MPS⑩ Micro Port Saver EEPROM with Block Lock⑩ Protection |
| X84640EG | Advanced MPS⑩ Micro Port Saver EEPROM with Block Lock⑩ Protection |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X76F641XG-2.0 | 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:Secure Serial Flash |
| X7800 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Core2 Duo Processors and Core2 Extreme Processors for Platforms Based on Mobile 965 Express Chipset Family |
| X7805 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:X78XX系列是三端正電源穩壓電路，它的封裝形式為TO-220.它有一系列固定的電壓輸出，應用非常廣泛。每種類型由于內部電流的限制，以及過熱保護和安全工作區的保護，使它基本上不會損壞。如果能夠提供足夠的散熱片，它們就能夠提供大于1.5A輸出電流。雖然是招安照固定電壓值來設計的，但是當接入適當?shù)耐獠科骷?，就能獲得各種不同的電壓和電流。 |
| X7809 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:X7809完美替代LM7809三端穩壓IC |
| X781 | 制造商:AIS 功能描述:17" ACTIVE MATRIX PANEL LCD - Bulk |
發布緊急采購，3分鐘左右您將得到回復。