- 您現在的位置：買賣IC網 > PDF目錄376444 > X60250 (Intersil Corporation) Micro Power Programmable Voltage Reference PDF資料下載
參數資料
| 型號： | X60250 |
| 廠商： | Intersil Corporation |
| 英文描述： | Micro Power Programmable Voltage Reference |
| 中文描述： | 微功耗可編程電壓基準 |
| 文件頁數： | 12/16頁 |
| 文件大?。?/td> | 382K |
| 代理商： | X60250 |
12
FN8146.1
September 14, 2005
Figure 6. Byte Write Sequence
Byte Write
For a write operation, the device requires the Slave
Address Byte and the Word Address Bytes. This gives
the master access to any one of the words in the array.
Upon receipt of each address byte, the X60250 responds
with an acknowledge. After receiving the address bytes
the X60250 awaits the eight bits of data. After receiving
the 8 data bits, the X60250 again responds with an
acknowledge. The master then terminates the transfer by
generating a stop condition. The X60250 then begins an
internal write cycle of the data to the nonvolatile memory.
During the internal write cycle, the device inputs are
disabled, so the device will not respond to any requests
from the master. The SDA output is at high impedance.
See Figure 6.
A write to a protected block of memory is ignored, but will
still receive an acknowledge. At the end of the write
command, the X60250 will not initiate an internal write
cycle, and will continue to okay commands.
Stops and Write Modes
Stop conditions that terminate write operations must be
sent by the master after sending at least 1 full data byte
and its associated ACK signal. If a stop is issued in the
middle of a data byte, or before 1 full data byte + ACK is
sent, then the X60250 resets itself without performing the
write. The contents of the array are not affected.
Figure 7. Random Address Read Sequence
Random Address Read
Random read operation allows the master to access any
location in the X60250. Prior to issuing the Slave
Address Byte, the master must first perform a “dummy”
write operation.
The master issues the start condition and the slave
address byte, receives an acknowledge, then issues the
word address bytes. After acknowledging receipt of each
word address byte, the master immediately issues
another start condition and the slave address byte. This
is followed by an acknowledge from the device and then
by the eight bit data word. The master terminates the
read operation by not responding with an acknowledge
and then issuing a stop condition. Refer to Figure 7 for
the address, acknowledge, and data transfer sequence.
In a similar operation called “Set Current Address,” the
device sets the address if a stop is issued instead of the
second start shown in Figure 7. The X60250 then goes
into standby mode after the stop and all bus activity will
be ignored until a start is detected. This operation loads
the new address into the address counter. The next
Current Address Read operation will read from the newly
loaded address. This operation could be useful if the
master knows the next address it needs to read, but is
not ready for the data.
S
t
a
r
t
S
t
o
p
Data
A
C
K
A
C
K
SDA Bus
Signals From
The Slave
Signals from
the Master
0
A
C
K
Byte
Address 0
0/1
0
0
0
1
0
1
Slave
Address*
Device
ID
*Note:
The X60250 will respond to either 000 or 001 slave addresses.
A
C
K
S
t
a
r
t
S
t
o
p
Data
S
t
a
r
t
SDA Bus
Signals from
the Slave
Signals from the
Master
Byte
Address 0
A
C
K
Slave
Address
0
0/1
0
0
0
1
0
1
Device
ID
A
C
K
Slave
Address
1
0
0
0
0
1
0
1
Device
ID
X60250
相關PDF資料 |
PDF描述 |
|---|---|
| x60250 | Micro Power Programmable Voltage Reference(微功耗可編程電壓基準) |
| X60250V8I | Micro Power Programmable Voltage Reference |
| X60250V8IZ | Micro Power Programmable Voltage Reference |
| X79002 | NV DAC with Selectable Output Range and Memory |
| X79000 | NV DAC with Selectable Output Range and Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X60250V8I | 功能描述:IC VREF SERIES ADJ 8-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:- 標準包裝:3,000 系列:- 基準類型:旁路，精度 輸出電壓:5V 容差:±0.5% 溫度系數:100ppm/°C 輸入電壓:- 通道數:1 電流 - 陰極:80µA 電流 - 靜態:- 電流 - 輸出:15mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:TO-236-3，SC-59，SOT-23-3 供應商設備封裝:SOT-23-3 包裝:帶卷 (TR) 其它名稱:LM4040CIM3-5.0MLTRLM4040CIM3-5.0MLTR-ND |
| X60250V8IZ | 功能描述:IC VREF SERIES ADJ 8-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:- 標準包裝:1 系列:- 基準類型:串聯，精度 輸出電壓:4.5V 容差:±800µV 溫度系數:1ppm/°C 輸入電壓:13.5 V ~ 22 V 通道數:1 電流 - 陰極:- 電流 - 靜態:7mA 電流 - 輸出:10mA 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:20-LCC 供應商設備封裝:20-CLCC 包裝:管件 |
| X60M000000L006 | 制造商:AEL Crystals Limited 功能描述:CRYSTAL 60MHZ HC49/U |
| X60R75 | 制造商:Teledyne Relays 功能描述:RELAY SSR 30MA 30V DC-IN 75A 690V AC-OUT 4-PIN - Bulk 制造商:Teledyne Industrial 功能描述: 制造商:Teledyne Relays 功能描述:SOLID STATE RELAY |
發布緊急采購，3分鐘左右您將得到回復。