- 您現在的位置：買賣IC網 > PDF目錄372533 > X40620V8E-2.9 Analog IC PDF資料下載
參數資料
| 型號： | X40620V8E-2.9 |
| 英文描述： | Analog IC |
| 中文描述： | 模擬IC |
| 文件頁數： | 5/22頁 |
| 文件大?。?/td> | 401K |
| 代理商： | X40620V8E-2.9 |
X4163/5 – Preliminary Information
Characteristics subject to change without notice.
5 of 22
REV 1.24 11/27/00
www.xicor.com
Figure 4. V
TRIP
Programming Sequence
V
TRIP
Programming
Apply 5V to V
CC
Decrement V
CC
(V
CC
= V
CC
- 50mV)
RESET pin
goes active
Measured V
TRIP
-
Desired V
TRIP
DONE
Execute
Reset V
TRIP
Sequence
Set V
CC
= V
CC
Applied =
Desired V
TRIP
Execute
Set V
Sequence
New V
CC
Applied =
Old V
CC
Applied + Error
Execute
Reset V
Sequence
New V
CC
Applied =
Old V
CC
Applied - Error
Error
≤
–Emax
–Emax < Error < Emax
YES
NO
Error
≥
Emax
Emax = Maximum Allowed V
TRIP
Error
Control Register
The Control Register provides the user a mechanism
for changing the Block Lock and Watchdog Timer set-
tings. The Block Lock and Watchdog Timer bits are
nonvolatile and do not change when power is removed.
The Control Register is accessed at address FFFFh. It
can only be modified by performing a byte write opera-
tion directly to the address of the register and only one
data byte is allowed for each register write operation.
Prior to writing to the Control Register, the WEL and
RWEL bits must be set using a two step process, with
the whole sequence requiring 3 steps. See "Writing to
the Control Register" below.
The user must issue a stop after sending this byte to
the register to initiate the nonvolatile cycle that stores
WD1, and WD0. The X4163/5 will not acknowledge
any data bytes written after the first byte is entered.
The state of the Control Register can be read at any
time by performing a random read at address FFFFh.
Only one byte is read by each register read operation.
相關PDF資料 |
PDF描述 |
|---|---|
| X40620V8E-3.1 | Analog IC |
| X40620V8E-3.1A | Analog IC |
| X40620 | RTC Module With CPU Supervisor |
| X4163 | RTC Module With CPU Supervisor |
| X4165 | RTC Module With CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X40620V8E-3.1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| X40620V8E-3.1A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| X40626 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Dual Voltage CPU Supervisor with 64K Serial EEPROM |
| X40626S14 | 功能描述:IC SUPERVISOR CPU DUAL 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40626S14-2.7 | 功能描述:IC SUPERVISOR CPU DUAL 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。