- 您現在的位置：買賣IC網 > PDF目錄372533 > X40620V8-3.1 8MHZ, TQFP, IND TEMP(MCU AVR) PDF資料下載
參數資料
| 型號： | X40620V8-3.1 |
| 英文描述： | 8MHZ, TQFP, IND TEMP(MCU AVR) |
| 中文描述： | 模擬IC |
| 文件頁數： | 10/22頁 |
| 文件大?。?/td> | 401K |
| 代理商： | X40620V8-3.1 |
X4163/5 – Preliminary Information
Characteristics subject to change without notice.
10 of 22
REV 1.24 11/27/00
www.xicor.com
Figure 10. Writing 12-bytes to a 64-byte page starting at location 60.
Address
n-1
Address
60
4 Bytes
8 Bytes
Address
= 7
Address Pointer
Ends Here
Addr =
8
The master terminates the Data Byte loading by issuing
a stop condition, which causes the device to begin the
nonvolatile write cycle. As with the byte write operation,
all inputs are disabled until completion of the internal
write cycle. See Figure 9 for the address, acknowledge,
and data transfer sequence.
Stops and Write Modes
Stop conditions that terminate write operations must
be sent by the master after sending at least 1 full data
byte plus the subsequent ACK signal. If a stop is
issued in the middle of a data byte, or before 1 full data
byte plus its associated ACK is sent, then the device
will reset itself without performing the write. The con-
tents of the array will not be effected.
Acknowledge Polling
The disabling of the inputs during nonvolatile cycles
can be used to take advantage of the typical 5ms write
cycle time. Once the stop condition is issued to indi-
cate the end of the master’s byte load operation, the
device initiates the internal nonvolatile cycle. Acknowl-
edge polling can be initiated immediately. To do this,
the master issues a start condition followed by the
Slave Address Byte for a write or read operation. If the
device is still busy with the nonvolatile cycle then no
ACK will be returned. If the device has completed the
write operation, an ACK will be returned and the host
can then proceed with the read or write operation.
Refer to the flow chart in Figure 11.
Figure 11. Acknowledge Polling Sequence
ACK
returned
Issue Slave Address
Byte (Read or Write)
Byte load completed
by issuing STOP.
Enter ACK Polling
Issue STOP
Issue START
NO
YES
Nonvolatile Cycle
complete. Continue
command sequence
Issue STOP
NO
Continue Normal
Read or Write
Command Sequence
PROCEED
YES
相關PDF資料 |
PDF描述 |
|---|---|
| X40620V8-3.1A | 8MHZ, MLF, IND TEMP, GREEN(MCU AVR) |
| X40620V8E-2.9 | Analog IC |
| X40620V8E-3.1 | Analog IC |
| X40620V8E-3.1A | Analog IC |
| X40620 | RTC Module With CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X40620V8E-2.9 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| X40620V8E-3.1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| X40620V8E-3.1A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| X40626 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Dual Voltage CPU Supervisor with 64K Serial EEPROM |
| X40626S14 | 功能描述:IC SUPERVISOR CPU DUAL 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。