- 您現在的位置：買賣IC網 > PDF目錄376440 > X4005M8-1.8 (INTERSIL CORP) RTC Module With CPU Supervisor PDF資料下載
參數資料
| 型號： | X4005M8-1.8 |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | RTC Module With CPU Supervisor |
| 中文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 封裝： | MSOP-8 |
| 文件頁數： | 3/17頁 |
| 文件大?。?/td> | 266K |
| 代理商： | X4005M8-1.8 |
3
FN8113.0
March 15, 2005
PRINCIPLES OF OPERATION
Power-on Reset
Application of power to the X4003/X4005 activates a
power-on reset circuit that pulls the RESET/RESET
pin active. This signal provides several benefits.
– It prevents the system microprocessor from starting
to operate with insufficient voltage.
– It prevents the processor from operating prior to
stabilization of the oscillator.
– It allows time for an FPGA to download its configura-
tion prior to initialization of the circuit.
When V
CC
exceeds the device V
TRIP
threshold value for
200ms (nominal) the circuit releases RESET/RESET,
allowing the system to begin operation.
Low Voltage Monitoring
During operation, the X4003/X4005 monitors the V
CC
level and asserts RESET/RESET if supply voltage falls
below a preset minimum V
TRIP
. The RESET/RESET
signal prevents the microprocessor from operating in a
power fail or brownout condition. The RESET/RESET
signal remains active until the voltage drops below 1V.
It also remains active until V
CC
returns and exceeds
V
TRIP
for 200ms.
Watchdog Timer
The watchdog timer circuit monitors the microproces-
sor activity by monitoring the SDA and SCL pins. The
microprocessor must toggle the SDA pin HIGH to
LOW periodically, while SCL also toggles from HIGH
to LOW (this is a start bit) followed by a stop condition
prior to the expiration of the watchdog time out period
to prevent a RESET/RESET signal. The state of two
nonvolatile control bits in the control register deter-
mine the watchdog timer period. The microprocessor
can change these watchdog bits, or they may be
“l(fā)ocked” by tying the WP pin HIGH.
Figure 1. Watchdog Restart
Set V
TRIP
Level Sequence (V
CC
= desired V
TRIP
value)
V
CC
THRESHOLD RESET PROCEDURE
The X4003/X4005 is shipped with a standard V
CC
threshold (V
TRIP
) voltage. This value will not change
over normal operating and storage conditions. How-
ever, in applications where the standard V
TRIP
is not
exactly right, or if higher precision is needed in the
V
TRIP
value, the X4003/X4005 threshold may be
adjusted. The procedure is described below, and uses
the application of a nonvolatile control signal.
Setting the V
TRIP
Voltage
This procedure is used to set the V
TRIP
to a higher
voltage value. For example, if the current V
TRIP
is 4.4V
and the new V
TRIP
is 4.6V, this procedure will directly
make the change. If the new setting is to be lower than
the current setting, then it is necessary to reset the trip
point before setting the new value.
SCL
SDA
.6μs
.6μs
Start
Condition
Stop
Condition
Restart
0
1
2
4
5 6
7
SCL
SDA
A0h
0
1
2 3
4
5 6
7
01h
WP
V
P
= 15-18V
0
1
2 3
4
5 6
7
00h
3
X4003, X4005
相關PDF資料 |
PDF描述 |
|---|---|
| X40233 | Triple Voltage Monitors, POR, 2 kbit EEPROM MEMORY, and Single/Dual DCP |
| X40235 | Triple Voltage Monitors, POR, 2 kbit EEPROM MEMORY, and Single/Dual DCP |
| X40237 | Triple Voltage Monitors, POR, 2 kbit EEPROM MEMORY, and Single/Dual DCP |
| X40239 | Triple Voltage Monitors, POR, 2 kbit EEPROM MEMORY, and Single/Dual DCP |
| X40420V14IZ-B | Dual Voltage Monitor with Intergrated CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X4005M8-2.7 | 功能描述:IC SUPERVISOR CPU I2C 8-MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X4005M8-2.7A | 功能描述:IC SUPERVISOR CPU I2C 8-MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X4005M8-4.5A | 功能描述:IC SUPERVISOR CPU I2C 8-MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X4005M8I | 功能描述:IC SUPERVISOR CPU I2C 8-MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X4005M8I-2.7 | 功能描述:IC SUPERVISOR CPU I2C 8-MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。