- 您現在的位置：買賣IC網 > PDF目錄371199 > X24165VI-2.7 Advanced 2-Wire Serial E2PROM with Block Lock Protection PDF資料下載
參數資料
| 型號： | X24165VI-2.7 |
| 英文描述： | Advanced 2-Wire Serial E2PROM with Block Lock Protection |
| 中文描述： | 先進的2線串行E2PROM區塊可鎖定的保護 |
| 文件頁數： | 7/17頁 |
| 文件大?。?/td> | 79K |
| 代理商： | X24165VI-2.7 |
X24165
7
Figure 7. Current Address Read
Figure 8. Random Read
READ OPERATIONS
Read operations are initiated in the same manner as
write operations with the exception that the R/W bit of
the slave address is set HIGH. There are three basic
read operations: current address read, random read
and sequential read.
It should be noted that the ninth clock cycle of the read
operation is not a “don’t care.” To terminate a read op-
eration, the master must either issue a stop condition
during the ninth cycle or hold SDA HIGH during the
ninth clock cycle and then issue a stop condition.
Current Address Read
Internally the X24165 contains an address counter that
maintains the address of the last word read, increment-
ed by one or the exact address of the last word written.
Therefore, if the last access read was to address n, the
next read operation would access data from address
n + 1. Upon receipt of the slave address with the R/W
set HIGH, the X24165 issues an acknowledge and
transmits the eight-bit word. The read operation is ter-
minated by the master; by not responding with an ac-
knowledge and by issuing a stop condition. Refer to
Figure 7 for the sequence of address, acknowledge
and data transfer.
Random Read
Random read operations allow the master to access
any memory location in a random manner. Prior to issu-
ing the slave address with the R/W bit set HIGH, the
master must first perform a “dummy” write operation.
The master issues the start condition, and the slave ad-
dress with the R/W bit set LOW, followed by the word
address it is to read. After the word address acknowl-
edge, the master immediately reissues the start condi-
tion and the slave address with the R/W bit set HIGH.
This will be followed by an acknowledge from the
X24165 and then by the eight-bit word. The read oper-
ation is terminated by the master; by not responding
with an acknowledge and by issuing a stop condition.
Refer to Figure 8 for the address, acknowledge and
data transfer sequence.
BUS ACTIVITY:
MASTER
SDA LINE
BUS ACTIVITY:
X24165
S
T
A
R
T
SLAVE
ADDRESS
S
S
T
O
P
P
A
C
K
DATA
6551 ILL F11
BUS ACTIVITY:
MASTER
SDA LINE
BUS ACTIVITY:
X24165
S
T
A
R
T
SLAVE
ADDRESS
S
A
C
K
6551 ILL F12.1
S
T
A
R
T
S
WORD
ADDRESS n
A
C
K
SLAVE
ADDRESS
DATA n
A
C
K
S
T
O
P
P
相關PDF資料 |
PDF描述 |
|---|---|
| X24165VM-2.7 | Advanced 2-Wire Serial E2PROM with Block Lock Protection |
| X24165S-2.7 | Advanced 2-Wire Serial E2PROM with Block Lock Protection |
| X24165P | Linear Voltage Regulator IC; Output Current Max:2A; Dropout Voltage, Vdo:300mV; Supply Voltage Max:5.5V; Package/Case:8-SOIC (EDP); Leaded Process Compatible:Yes; Operating Temp. Max:85 C; Operating Temp. Min:-40 C |
| X24165P-2.7 | IC LDO REG 3A 5.5V W/ENBL 8-SOIC |
| X24165PI | Hot Swap Controller IC; Hot Swap Controller Type:Negative Voltage; Controlled Voltage Min:-10V; Controlled Voltage Max:-80V; Number of Controlled Voltages:1; Package/Case:8-SOIC; Power Good Output:Active High |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X24165VIG | 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:Advanced 2-Wire Serial E2PROM with Block LockTM Protection |
| X24165VIG-2.7 | 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:Advanced 2-Wire Serial E2PROM with Block LockTM Protection |
| X24165VM | 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:Advanced 2-Wire Serial E2PROM with Block LockTM Protection |
| X24165VM-2.7 | 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:Advanced 2-Wire Serial E2PROM with Block LockTM Protection |
| X24165VMG | 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:Advanced 2-Wire Serial E2PROM with Block LockTM Protection |
發布緊急采購，3分鐘左右您將得到回復。