- 您現在的位置：買賣IC網 > PDF目錄203632 > W78M64120SBI (MICROSEMI CORP-PMG MICROELECTRONICS) 8M X 64 FLASH 3.3V PROM, 120 ns, PBGA159 PDF資料下載
參數資料
| 型號： | W78M64120SBI |
| 廠商： | MICROSEMI CORP-PMG MICROELECTRONICS |
| 元件分類： | PROM |
| 英文描述： | 8M X 64 FLASH 3.3V PROM, 120 ns, PBGA159 |
| 封裝： | 13 X 22 MM, 1.27 MM PITCH, PLASTIC, BGA-159 |
| 文件頁數： | 3/50頁 |
| 文件大小： | 1679K |
| 代理商： | W78M64120SBI |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
11
White Electronic Designs Corporation (602) 437-1520 www.whiteedc.com
White Electronic Designs
W78M64VP-XSBX
November 2009
2010 White Electronic Designs Corp. All rights reserved
Rev. 10
White Electronic Designs Corp. reserves the right to change products or specications without notice.
HARDWARE RESET
The RESET# input provides a hardware method of resetting
the device to reading array data. When RESET# is driven
low for at least a period of tRP (RESET# Pulse Width), the
device immediately terminates any operation in progress,
tristates all outputs, resets the conguration register, and
ignores all read/write commands for the duration of the
RESET# pulse. The device also resets the internal state
machine to reading array data.
To ensure data integrity Program/Erase operations that were
interrupted should be reinitiated once the device is ready to
accept another command sequence.
When RESET# is held at VSS, the device draws VCC reset
current (ICC5). If RESET# is held at VIL, but not at VSS, the
standby current is greater. RESET# may be tied to the
system reset circuitry which enables the system to read the
boot-up rmware from the Flash memory upon a system
reset.
SOFTWARE RESET
Software reset is part of the command set (see Table 12.1
on page 69) that also returns the device to arrayread mode
and must be used for the following conditions:
1. to exit Autoselect mode
2. when DQ5 goes high during write status operation that
indicates program or erase cycle was not successfully
completed
3. exit sector lock/unlock operation.
4. to return to erase-suspend-read mode if the device was
previously in Erase Suspend mode.
5. after any aborted operations
The following are additional points to consider when using
the reset command:
This command resets the sectors to the read and
address bits are ignored.
Reset commands are ignored during program and
erase operations.
The reset command may be written between the
cycles in a program command sequence before
programming begins (prior to the third cycle). This
resets the sector to which the system was writing to
the read mode.
If the program command sequence is written to a
sector that is in the Erase Suspend mode, writing
the reset command returns that sector to the erase-
suspend-read mode.
The reset command may be written during an
Autoselect command sequence.
If a sector has entered the Autoselect mode while
in the Erase Suspend mode, writing the reset
command returns that sector to the erase-suspend-
read mode.
If DQ1 goes high during a Write Buffer Programming
operation, the system must write the “Write to Buffer
abort Reset” command sequence to RESET the
device to reading array data. The standard RESET
command does not work during this condition.
To exit the unlock bypass mode, the system must
issue a two-cycle unlock bypass reset command
sequence [see Command Denitions for details].
ADVANCED SECTOR PROTECTION/
UNPROTECTION
The Advanced Sector Protection/Unprotection feature
disables or enables programming or erase operations in any
or all sectors and can be implemented through software and/
or hardware methods, which are independent of each other.
This section describes the various methods of protecting
data stored in the memory array. An overview of these
methods in shown in FIG: 8.
LOCK REGISTER
As shipped from the factory, all devices default to the
persistent mode when power is applied, and all sectors
are unprotected. The device programmer or host system
must then choose which sector protection method to use.
Programming (setting to “0”) any one of the following two
one-time programmable, non-volatile bits locks the part
permanently in that mode:
Lock Register Persistent Protection Mode Lock Bit
(DQ1)
Lock Register Password Protection Mode Lock Bit
(DQ2)
相關PDF資料 |
PDF描述 |
|---|---|
| W78M64110SBC | 8M X 64 FLASH 3.3V PROM, 110 ns, PBGA159 |
| W78M64V100SBC | 8M X 64 FLASH 3.3V PROM MODULE, 100 ns, PBGA159 |
| W78M64VP120SBM | SPECIALTY MEMORY CIRCUIT, PBGA156 |
| W78M64VP120SBI | SPECIALTY MEMORY CIRCUIT, PBGA156 |
| W83L761G | DIGITAL TEMP SENSOR-SERIAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W78M64VP110SBM | 制造商:Microsemi Corporation 功能描述:8MX64 FLASH 3.3V PAGE MODE - Bulk |
| W78M64V-XSBX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Flash MCP |
| W78NCSX-23 | 功能描述:低信號繼電器 - PCB 4PDT 3A 24VDC IND RoHS:否 制造商:NEC 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 V 最大開關電流:1 A 線圈電流:1 A 線圈類型:Non-Latching 功耗:140 mW 端接類型:SMT 絕緣: 介入損耗: |
| W78PCX-1 | 制造商:Magnecraft 功能描述: |
| W78PCX-2 | 制造商:Magnecraft 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。