- 您現在的位置：買賣IC網 > PDF目錄203632 > W78M64110SBC (WHITE ELECTRONIC DESIGNS CORP) 8M X 64 FLASH 3.3V PROM, 110 ns, PBGA159 PDF資料下載
參數資料
| 型號： | W78M64110SBC |
| 廠商： | WHITE ELECTRONIC DESIGNS CORP |
| 元件分類： | PROM |
| 英文描述： | 8M X 64 FLASH 3.3V PROM, 110 ns, PBGA159 |
| 封裝： | 13 X 22 MM, 1.27 MM PITCH, PLASTIC, BGA-159 |
| 文件頁數： | 48/50頁 |
| 文件大?。?/td> | 1679K |
| 代理商： | W78M64110SBC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁當前第48頁第49頁第50頁
7
White Electronic Designs Corporation (602) 437-1520 www.whiteedc.com
White Electronic Designs
W78M64VP-XSBX
November 2009
2010 White Electronic Designs Corp. All rights reserved
Rev. 10
White Electronic Designs Corp. reserves the right to change products or specications without notice.
The Unlock Bypass feature allows the host system to send
program commands to the Flash device without rst writing
unlock cycles within the command sequence. See Unlock
Bypass Section for details on the Unlock Bypass function.
Any commands written during the chip erase operation are
ignored. However, note that a hardware reset immediately
terminates the erase operation. If that occurs, the chip erase
command sequence should be reinitiated once that sector
has returned to reading array data, to ensure the entire
array is properly erased.
ERASE SUSPEND/ERASE RESUME
COMMANDS
The Erase Suspend command allows the system to interrupt
a sector erase operation and then read data from, or
program data to, any sector not selected for erasure. The
sector address is required when writing this command. This
command is valid only during the sector erase operation,
including the minimum tSEA time-out period during the sector
erase command sequence. The Erase Suspend command
is ignored if written during the chip erase operation.
When the Erase Suspend command is written during the
sector erase operation, the device requires a maximum of 20
μs (5 μs typical) to suspend the erase operation. However,
when the Erase Suspend command is written during the
sector erase time-out, the device immediately terminates
the time-out period and suspends the erase operation.
After the erase operation has been suspended, the device
enters the erase-suspend-read mode. The system can
read data from or program data to any sector not selected
for erasure. (The device “erase suspends” all sectors
selected for erasure.) Reading at any address within
erase-suspended sectors produces status information on
DQ7-DQ0. The system can use DQ7, or DQ6, and DQ2
together, to determine if a sector is actively erasing or is
erase-suspended.
After an erase-suspended program operation is complete,
the device returns to the erase-suspend-read mode. The
system can determine the status of the program operation
using write operation status bits, just as in the standard
program operation.
In the erase-suspend-read mode, the system can also issue
the Autoselect command sequence. Refer to Write Buffer
Programming Section and the Autoselect Section.
To resume the sector erase operation, the system must write
the Erase Resume command. The address of the erase-
suspended sector is required when writing this command.
Further writes of the Resume command are ignored.
Another Erase Suspend command can be written after the
chip has resumed erasing.
PROGRAM SUSPEND/PROGRAM
RESUME COMMANDS
The Program Suspend command allows the system
to interrupt an embedded programming operation or a
“Write to Buffer” programming operation so that data can
read from any non-suspended sector. When the Program
Suspend command is written during a programming
process, the device halts the programming operation within
15 μs maximum (5 μs typical) and updates the status bits.
Addresses are “don't-cares” when writing the Program
Suspend command.
After the programming operation has been suspended, the
system can read array data from any nonsuspended sector.
The Program Suspend command may also be issued during
a programming operation while an erase is suspended. In
this case, data may be read from any addresses not within
a sector in Erase Suspend or Program Suspend. If a read
is needed from the Secured Silicon Sector area, then user
must use the proper command sequences to enter and
exit this region.
The system may also write the Autoselect Command
Sequence when the device is in Program Suspend
mode. The device allows reading Autoselect codes in the
suspended sectors, since the codes are not stored in the
memory array. When the device exits the Autoselect mode,
the device reverts to Program Suspend mode, and is ready
for another valid operation. See Autoselect Section.
After the Program Resume command is written, the device
reverts to programming. The system can determine the
status of the program operation using the write operation
status bits, just as in the standard program operation. See
Write Operation Status Section for more information.
The system must write the Program Resume command
(address bits are “don't care”) to exit the Program Suspend
mode and continue the programming operation. Further
writes of the Program Resume command are ignored.
Another Program Suspend command can be written after
the device has resumed programming.
相關PDF資料 |
PDF描述 |
|---|---|
| W78M64V100SBC | 8M X 64 FLASH 3.3V PROM MODULE, 100 ns, PBGA159 |
| W78M64VP120SBM | SPECIALTY MEMORY CIRCUIT, PBGA156 |
| W78M64VP120SBI | SPECIALTY MEMORY CIRCUIT, PBGA156 |
| W83L761G | DIGITAL TEMP SENSOR-SERIAL |
| W8D-PF29062 | 36 CONTACT(S), FEMALE, STRAIGHT SINGLE PART CARD EDGE CONN, PRESS FIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W78M64VP110SBM | 制造商:Microsemi Corporation 功能描述:8MX64 FLASH 3.3V PAGE MODE - Bulk |
| W78M64V-XSBX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Flash MCP |
| W78NCSX-23 | 功能描述:低信號繼電器 - PCB 4PDT 3A 24VDC IND RoHS:否 制造商:NEC 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 V 最大開關電流:1 A 線圈電流:1 A 線圈類型:Non-Latching 功耗:140 mW 端接類型:SMT 絕緣: 介入損耗: |
| W78PCX-1 | 制造商:Magnecraft 功能描述: |
| W78PCX-2 | 制造商:Magnecraft 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。