- 您現在的位置：買賣IC網 > PDF目錄359455 > W172DIP-5 RELAY REED DIL 5VDC PDF資料下載
參數資料
| 型號： | W172DIP-5 |
| 英文描述： | RELAY REED DIL 5VDC |
| 中文描述： | 勵迪勒5Vdc時繼電器 |
| 文件頁數： | 95/210頁 |
| 文件大?。?/td> | 7067K |
| 代理商： | W172DIP-5 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁當前第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁
20 40 60 80 100
Max. Ambient Temperature (C)
25
40
30
35
20
15
10
5
0
Free Air Mounting
Mounted on Heat Sink with 1c/w
thermal resistance.
(Sink to Ambient)
6" x 6" x 1/8"
Aluminum
Plate
L
25 Amp Styles
TRANSFORMERS
In controlling transformers, the characteristics of the secondary load should
be considered because it reflects the effective load on the SSR. Voltage
transients from secondary load circuits, similarly, are frequently transformed
and can be imposed on the SSR. Transformers present a special problem
in that, depending on the state of the transformer flux at the time of turnoff,
the transformer may saturate during the first half-cycle of subsequent
applied voltage. This saturation can impose a very large current (Com-
monly ten to one hundred times rated primary current) on the SSR and
exceed its half-cycle surge rating.
SSR's having random turn-on may have a better chance of survival than a
zero voltage turn-on device for they commonly require the transformer to
support only a portion of the first half-cycle of the voltage. On the other
hand, a random turn-on device will frequently close at the essentially zero
voltage point (start of the half-cycle) and then the SSR must sustain the
worst-case saturation current. A zero voltage turn-on device has the
advantage that it turns on in a known, predictable mode and will normally
immediately demonstrate (dependent on turnoff flux polarity) the worst-case
condition. The use of an oscilloscope is recommended to verify that the
half-cycle surge capability of the SSR is not exceeded. The severity of the
transformer saturation problem varies greatly, dependent on the magnetic
material of the transformer, saturated primary impedance, line impedance,
etc.
A safe rule of thumb in applying an SSR to a transformer primary is to select
an SSR having a half-cycle current surge rating (RMS) greater than the
maximum applied line voltage (RMS) divided by the transformer primary
resistance. The primary resistance is usually easily measured and can be
relied on as a minimum impedance limiting the first half-cycle of inrush
current. The presence of some residual flux plus the saturated reactance of
the primary will then further limit, in the worst case, the half-cycle surge
safely within the surge rating of the SSR.
SELECTING THE PROPER SSR
NOMINAL LOAD CURRENT: Initially select a relay whose current rating
exceeds the normal load current. Using the load current vs. temperature
chart for that relay, check the actual current capacity at the ambient
temperature to which the relay will be subjected.
As an example, the chart below shows that a 25 ampere relay provided with
a suitable heat sink can safely carry a maximum of 17 amperes continu-
ously at 40C ambient. Since heat degrades the output semiconductor
every effort should be made to keep the operating temperature of the SSR
as low as possible
dv
dt
V =
I =
( Load Power Factor
f =
Inductance in Henrys
Capacitance in microfarads
R
2
=
& R
EXPRESSIONS USED IN SPECIFICATIONS
equals the maximum permissable rate of change
of voltage in volts/microseconds
Line Voltage
Load Current
Line Frequency
PROTECTING THE OUTPUT SWITCH
An SSR is a four layer semiconductor having 3 terminals:
Cathode, Anode and Gate. Normally it blocks current in both the
forward and reverse directions. The SCR is triggered on in the
forward direction by a small gate current. The SCR remains on
until load current decreases to a value less than necessary to
maintain the SCR in the on state. When switching AC, two SSR's
are connected in inverse parallel.
A Triac also has 3 terminals, like the SCR, it normally blocks
current in both directions; but may be triggered in either direction
by a small gate current
Both SCR's and Triacs are members of the thyristor family.
Therefore, we use this term to denote both devices. There are 4
ways to put a thyristor into a conducting mode. Only one method
is desirable and the other three are the source of most application
problems.
The 4 methods of Thyristor turn-on are -
A. Gate Turn-on: By injecting a controlled current into the gate
(the desired method).
B. Forward Breakover Turn-on: A voltage in excess of the
Breakover (or Peak Blocking) voltage across Thyristor.
C. DV/DT turn-on: A voltage which rises faster than the Thyristor
can tolerate, and still remain in the off state.
D. Thermal Turn-on: Allowing the temperature of the thyristor to
go beyond the value sufficient to cause excessive leakage
current, causing turn-on and possible thermal runaway.
The last three methods can be protected against as follows. In
those situations where high peak voltage transients occur, effective
protection can be obtained by using metal oxide varistors (MOV).
The MOV is a bidirectional voltage sensitive device that has low
impedance when its design voltage threshold is exceeded.
HEAT SINKING
It is important to select the right size heat sink for your applications.
SSR's will typically generate 1.2 watts per amp of load current.
The maximum junction temperature of the output device is 115C.
The total wattage is divided by the thermal resistance to get the
temperature difference between the output device junction and the
ambient temperature. For example a 25 Amp SSR with a 20 Amp
load applied dissipates 24 watts when mounted on a aluminum
plate 6" X 6" X 1/8" with thermal grease applied between the SSR
base and aluminum plate. This combination produces a output
junction temperature rise of 24 watts. 24W times (1 c/w relay +
1 c/w (heat sink) = a operating temperature of 48C.
FUSING
THE SSR has a I
2
T rating which is a measure of the amount of
energy it can safely handle without damage. The I
2
T rating of the
fuse is a measure of the amount of energy the fuse will pass to the
SSR. To protect the SSR, the I
2
T of the Fuse should be less than
that of the SSR. An SSR exposed to a surge greater than its non-
repetitive rating will normally fail as a shorted unit.
PAGE 95
WEBSITE: www.magnecraft.com EMAIL:info@magnecraft.com FAX ON DEMAND 1-800/891-2957, DOCUMENT 100
C L A S S
SSR
APPLICATION DATA
相關PDF資料 |
PDF描述 |
|---|---|
| W172DIP-150 | RELAY REED DIL 24VDC |
| W49RE1C2VF-6DC-SCO | SCHALTRELAIS SPCO |
| W49RE1C2VF-12DC-SCO | SCHALTRELAIS SPCO |
| W171DIP-9 | RELAY REED DIL 12VDC |
| W171DIP-7 | RELAY REED DIL 5VDC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W172DIP-6 | 制造商:Magnecraft 功能描述: |
| W172DIP-7 | 功能描述:簧片繼電器 172DIP Mini Reed PCB Relay / SPDT, 0.25 A RoHS:否 制造商:MEDER electronic (Standex) 觸點形式:1 Form A (SPST-NO) 線圈電壓:5 VDC 最大開關功率:100 W 最大開關電流:1 A 線圈抑制二極管:No 線圈電阻:220 Ohms 端接類型: |
| W172DIP-8 | 功能描述:簧片繼電器 172DIP Mini Reed PCB Relay / SPDT, 0.25 A RoHS:否 制造商:MEDER electronic (Standex) 觸點形式:1 Form A (SPST-NO) 線圈電壓:5 VDC 最大開關功率:100 W 最大開關電流:1 A 線圈抑制二極管:No 線圈電阻:220 Ohms 端接類型: |
| W172E11 | 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:C200H VOICE OUTPUT MAN DX CODE ZA |
| W172SIP-4 | 制造商:Magnecraft 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。