- 您現在的位置：買賣IC網 > PDF目錄225531 > VRE410LS THREE TERM VOLTAGE REFERENCE, PDSO14 PDF資料下載
參數資料
| 型號： | VRE410LS |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | THREE TERM VOLTAGE REFERENCE, PDSO14 |
| 封裝： | DSO-14 |
| 文件頁數： | 4/5頁 |
| 文件大小： | 404K |
| 代理商： | VRE410LS |
DISCUSSION OF PERFORMANCE
VRE410DS REV. A MAY 1996
VRE410
FIGURE 2
THEORY OF OPERATION
The following discussion refers to the schematic
below. In operation, approximately 6.3 volts is
applied to the noninverting input of the op amp. The
voltage is amplified by the op amp to produce a
10.000V output. The gain is determined by the
networks R1 and R2: G=1 + R2/R1. The 6.3V zener
diode is used because it is the most stable diode
over time and temperature.
The zener operating current is derived from the
regulated output voltage through R3. This feedback
arrangement provides a closely regulated zener
current. This current determines the slope of the
references' voltage vs. temperature function. By
trimming the zener current a lower drift over
temperature can be achieved. But since the voltage
vs.
temperature
function
is
nonlinear
this
compensation technique is not well suited for wide
temperature ranges.
Thaler Corporation has developed a nonlinear
compensation network of thermistors and resistors
that is used in the VRE series voltage references.
This proprietary network eliminates most of the
nonlinearity in the voltage vs. temperature function.
By then adjusting the slope, Thaler Corporation
produces
a
very
stable
voltage
over
wide
temperature ranges.
The VRE400 series voltage references have the
ground terminal brought out on two pins (pin 6 and 7)
which are connected together internally. This allows
the user to achieve greater accuracy when using a
socket. Voltage references have a voltage drop
across their power supply ground pin due to
quiescent
current
flowing
through
the
contact
resistance. If the contact resistance was constant
with time and temperature, this voltage drop could be
trimmed out. When the reference is plugged into a
socket, this source of error can be as high as 20ppm.
By connecting pin 7 to the power supply ground and
pin 6 to a high impedance ground point in the
measurement circuit, the error due to the contact
resistance can be eliminated. If the unit is soldered
into place the contact resistance is sufficiently small
that it doesn't effect performance.
相關PDF資料 |
PDF描述 |
|---|---|
| VRNB-40A18B | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| VRW150-28A | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| VS-500-LFF-GNN-669.128MHZ | VOLTAGE CONTROLLED CLOCK SAW OSCILLATOR, 669.128 MHz |
| VS-500-LFF-GNN-777.6MHZ | VOLTAGE CONTROLLED CLOCK SAW OSCILLATOR, 777.6 MHz |
| VS-500-LFF-GNN-767.25MHZ | VOLTAGE CONTROLLED CLOCK SAW OSCILLATOR, 767.25 MHz |
相關代理商/技術參數 |
參數描述 |
|---|---|
| VRE4110B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low Cost, SOIC-8 Precision References |
| VRE4110C | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low Cost, SOIC-8 Precision References |
| VRE4110K | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low Cost, SOIC-8 Precision References |
| VRE4112 | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:Precision Voltage Reference |
| VRE4112B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low Cost, SOIC-8 Precision References |
發布緊急采購，3分鐘左右您將得到回復。