- 您現在的位置：買賣IC網 > PDF目錄359409 > VP1058FCGHPAS (ZARLINK SEMICONDUCTOR INC) 8-BIT, 25MHz, VIDEO FLASH ADC (SINGLE + 5V SUPPLY) PDF資料下載
參數資料
| 型號： | VP1058FCGHPAS |
| 廠商： | ZARLINK SEMICONDUCTOR INC |
| 元件分類： | ADC |
| 英文描述： | 8-BIT, 25MHz, VIDEO FLASH ADC (SINGLE + 5V SUPPLY) |
| 中文描述： | 1-CH 8-BIT FLASH METHOD ADC, PARALLEL ACCESS, PQCC28 |
| 封裝： | PLASTIC, HP-28 |
| 文件頁數： | 8/11頁 |
| 文件大?。?/td> | 430K |
| 代理商： | VP1058FCGHPAS |
VP1058
APPLICATION NOTES
As with all high speed analog-to-digital converters, careful
consideration must be given to circuit layout. The best
performance from the VP1058 can be achieved by use of
separate analog and digital ground planes. Ideally these
should be connected at a point close to the device. This will
reduce the amount of digital switching noise fed back into the
analog section of the converter, so aiding device performance.
Supply line decoupling is important when dealing with
mixed analog and digital signals, as they can provide a
feedback path from the digital output currents. Therefore, the
VP1058 should be decoupled close to the device supply pins
with good quality high frequency, low inductance capacitors.
Due to the high clock rates, long clock lines to the device
should be avoided to reduce noise pick up.
A typical applications circuit is shown below. The analog
input amplifier should be a wideband, high slew rate op-amp
used to drive the input directly. A stable reference is needed
for both input offset and gain control (e.g. REF12Z micropower
voltage reference as shown in Fig.6). Both analog input pins
should be connected close to the device with the input
amplifiers feedback loop closed at the point. The reference
inputs should be adequately decoupled to ground so as to limit
the effects of system noise on conversion accuracy. A
capacitor at the mid-reference point (as shown) may be useful
in correcting any inherent reference ladder skew.
The circuit will accept a 1V p-p video signal and level shift
and multiply it to provide the recommended 2V p-p signal to
drive the VP1058.
1
DB7
28
NMINV
12
LNINV
2
DB6
3
DB5
4
DB4
13
DB3
14
DB2
15
DB1
16
DB0
+
-
-
+
+
-
+5V
DV
CC
+5V
AV
CC
+5V
AV
CC
AV
CC
DV
CC
V
RT
18
V
RB
26
V
RM
27
A
IN
21
A
IN
23
CONV
17
DGND
5, 11
AGND
7, 8, 9
+5V
0.1μ
0.1μ
1N4148
0.1μ
0.1μ
6, 10
19, 25
+12V
2N2222
TAB1043
0.1μ
6K2
2K
2.9k
3.3k
1k
+12V
0.1μ
3k
TAB1043
2N2907
REFGAIN
AD842 OR SIMILAR
1k
REF12Z
(1.22V
REFERENCE)
2k
1k
1k
1k
50
ANALOG
INPUT
(V
ANIN
)
0.1μ
1.3k
0.1μ
2k
OFFSET
CLOCK
V
O
V
OUT
V
REF
390
VP1058
Fig.6 Typical applications circuit
相關PDF資料 |
PDF描述 |
|---|---|
| VP1058FCGDPAS | 8-BIT, 25MHz, VIDEO FLASH ADC (SINGLE + 5V SUPPLY) |
| VP1058FCGDGAS | 8-BIT, 25MHz, VIDEO FLASH ADC (SINGLE + 5V SUPPLY) |
| VP1106N2 | PT 19C 19#20 PIN PLUG |
| VP1106N5 | P-Channel Enhancement-Mode Vertical DMOS Power FETs |
| VP1106ND | P-Channel Enhancement-Mode Vertical DMOS Power FETs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| VP1058J | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter， 8-Bit |
| VP1058Q | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter， 8-Bit |
| VP-10676 | 功能描述:基本/快動開關 V BASIC SW RoHS:否 制造商:Omron Electronics 觸點形式:SPDT 執行器:Lever 電流額定值:5 A 電壓額定值 AC:250 V 電壓額定值 DC:30 V 功率額定值: 工作力:120 g IP 等級:IP 67 NEMA 額定值: 端接類型:Wire 安裝:Panel |
| VP10BK | 功能描述:電纜組件 VIDEO PATCH CD BLK C RoHS:否 制造商:Molex 產品:Power Assemblies 類型:Cable Assembly 連接器端口 A:No Connector 連接器端口 A 管腳計數:4 連接器端口 B:No Connector 連接器端口 B 管腳計數: 型式:Male 線規 - 美國線規（AWG）:20, 28 長度:0.305 m 顏色:Black, Red |
| VP10BKX | 功能描述:PATCHCORD VIDEO STD 10' BLACK RoHS:是 類別:電纜組件 >> 視頻 - DVI，HDMI，WECo 系列:VP 標準包裝:1 系列:- 連接器類型:Mini-WECo 公形至 WECo 公形 長度:8.0'（2.44m） 纜線類型:圓形 顏色:黑 屏蔽:無屏蔽 使用:- |
發布緊急采購，3分鐘左右您將得到回復。