- 您現在的位置：買賣IC網 > PDF目錄359784 > VNQ690SPTR-E (意法半導體) QUAD CHANNEL HIGH SIDE DRIVER PDF資料下載
參數資料
| 型號： | VNQ690SPTR-E |
| 廠商： | 意法半導體 |
| 英文描述： | QUAD CHANNEL HIGH SIDE DRIVER |
| 中文描述： | 四通道高邊驅動器 |
| 文件頁數： | 9/20頁 |
| 文件大?。?/td> | 203K |
| 代理商： | VNQ690SPTR-E |
9/20
VNQ690SP-E
Figure 8. Application Schematic
GND
REVERSE BATTERY
Solution 1: Resistor in the ground line (R
GND
only). This
can be used with any type of load.
The following is an indication on how to dimension the
R
GND
resistor.
1) R
GND
≤
600mV / (I
S(on)max
).
2) R
GND
≥ (
V
CC
) / (-I
GND
)
where -I
GND
is the DC reverse ground pin current and can
be found in the absolute maximum rating section of the
device’s datasheet.
Power Dissipation in R
GND
(when V
CC
<0: during reverse
battery situations) is:
P
D
= (-V
CC
)
2
/R
GND
This resistor can be shared amongst several different
HSD. Please note that the value of this resistor should be
calculated with formula (1) where I
S(on)max
becomes the
sum of the maximum on-state currents of the different
devices.
Please note that if the microprocessor ground is not
common with the device ground then the R
will
produce a shift (I
S(on)max
* R
GND
) in the input thresholds
and the status output values. This shift will vary
depending on how many devices are ON in the case of
several high side drivers sharing the same R
GND
.
PROTECTION
NETWORK
AGAINST
If the calculated power dissipation leads to a large
resistor or several devices have to share the same
resistor then the ST suggests to utilize Solution 2 (see
below).
Solution 2: A diode (D
GND
) in the ground line.
A resistor (R
GND
=1k
)
should be inserted in parallel to
D
GND
if the device will be driving an inductive load.
This small signal diode can be safely shared amongst
several different HSD. Also in this case, the presence of
the ground network will produce a shift (
j
600mV) in the
input threshold and the status output values if the
microprocessor ground is not common with the device
ground. This shift will not vary if more than one HSD
shares the same diode/resistor network.
Series resistor in INPUT and STATUS lines are also
required to prevent that, during battery voltage transient,
the current exceeds the Absolute Maximum Rating.
Safest configuration for unused INPUT and STATUS pin
is to leave them unconnected.
LOAD DUMP PROTECTION
D
ld
is necessary (Voltage Transient Suppressor) if the
load dump peak voltage exceeds V
CC
max DC rating.
The same applies if the device will be subject to
transients on the V
CC
line that are greater than the ones
shown in the ISO T/R 7637/1 table.
V
CC
D
ld
+5V
R
prot
STATUS
INPUT1
+5V
OUTPUT3
OUTPUT1
OUTPUT2
OUTPUT4
INPUT3
INPUT4
R
prot
R
prot
R
prot
R
prot
INPUT2
μ
C
GND
D
GND
R
GND
V
GND
Note: Channels 3 & 4 have the same internal circuit as channel 1 & 2.
相關PDF資料 |
PDF描述 |
|---|---|
| VM6101V008 | IC color light sensor |
| VM6101V008TR | IC color light sensor |
| V321ID | General Purpose, Input/Output Rail-to-Rail Low Power Operational Amplifiers |
| V324ID | General Purpose, Input/Output Rail-to-Rail Low Power Operational Amplifiers |
| V324IP | General Purpose, Input/Output Rail-to-Rail Low Power Operational Amplifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| VNQ7140AJ-E | 制造商:STMicroelectronics 功能描述:ABD VIPOWER - Rail/Tube |
| VNQ7140AJTR | 功能描述:IC DVR HIGH-SIDE 4CH PWRSSO16 制造商:stmicroelectronics 系列:VIPower?? 包裝:剪切帶（CT） 零件狀態:有效 開關類型:通用 輸出數:4 比率 - 輸入:輸出:1:1 輸出配置:高端 輸出類型:N 通道 接口:開/關 電壓 - 負載:4 V ~ 28 V 電壓 - 電源（Vcc/Vdd）:不需要 電流 - 輸出（最大值）:8A 導通電阻（典型值）:140 毫歐 輸入類型:非反相 特性:自動重啟，狀態標志 故障保護:限流（固定），開路負載檢測，超溫，過壓，UVLO 工作溫度:-40°C ~ 150°C（TJ） 封裝/外殼:16-PowerLFSOP（0.154"，3.90mm 寬） 供應商器件封裝:PowerSSO-16 標準包裝:1 |
| VNQ7140AJTR-E | 制造商:STMicroelectronics 功能描述:ABD VIPOWER - Tape and Reel 制造商:STMicroelectronics 功能描述:IC DVR HIGH-SIDE QUAD POWERSSO16 |
| VNQ810 | 功能描述:功率驅動器IC Quad Channel Hi-Side RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| VNQ810 | 制造商:STMicroelectronics 功能描述:IC, MOSFET, SMART SWITCH, SO-28 |
發布緊急采購，3分鐘左右您將得到回復。