- 您現在的位置：買賣IC網 > PDF目錄225472 > USB2602-NU-04 (STANDARD MICROSYSTEMS CORP) PDF資料下載
參數資料
| 型號： | USB2602-NU-04 |
| 廠商： | STANDARD MICROSYSTEMS CORP |
| 元件分類： | 存儲控制器/管理單元 |
| 中文描述： | FLASH MEMORY DRIVE CONTROLLER, PQFP128 |
| 封裝： | 14 X 14 MM, 1 MM HEIGHT, GREEN, TQFP-128 |
| 文件頁數： | 9/26頁 |
| 文件大?。?/td> | 421K |
| 代理商： | USB2602-NU-04 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
4th Generation USB2.0 Flash Media Controller with Integrated Card Power FETs and HS Hub
Datasheet
SMSC USB2601/USB2602
17
Revision 1.5 (07-24-06)
DATASHEET
SM
Chip Enable
SM_nCE
O8PU
This pin is the active low chip enable signal to the SM
device.
When using the internal FET, this pin has an internal
weak pull-up resistor that is tied to the output of the
internal Power FET.
08
If an external FET is used (Internal FET is disabled),
then the internal pull-up is not available (external pull-
ups must be used, and should be connected to the
applicable Card Power Supply).
SM
Card Detection
SM_nCD
IPU
This is the card detection signal from SM device to
indicate if the device is inserted.
This pin has an internally controlled weak pull-up
resistor.
MEMORY STICK INTERFACE
MS
Bus State
MS_BS
O8
This pin is connected to the BS pin of the MS device.
It is used to control the Bus States 0, 1, 2 and 3 (BS0,
BS1, BS2 and BS3) of the MS device.
MS
System
Data In/Out
MS_SDIO/MS_
D0
I/O8PD
This pin is a bi-directional data signal for the MS device.
Most significant bit (MSB) of each byte is transmitted
first by either MSC or MS device.
The bi-directional data signal has an internal weak pull-
down resistor.
MS
System Data In/Out
MS_D1
I/O8PD
This pin is a bi-directional data signal for the MS device.
This pin has internally controlled weak pull-up and pull-
down resistors for various operational modes.
MS
System
Data In/Out
MS_D[3:2]
I/O8PD
This pin is a bi-directional data signal for the MS device.
The bi-directional data signal has an internal weak pull-
down resistor.
MS
Card Insertion
MS_INS
IPU
This pin is the card detection signal from the MS device
to indicate, if the device is inserted.
This pin has an internally controlled weak pull-up
resistor.
MS
System CLK
MS_SCLK
O8
This pin is an output clock signal to the MS device.
The clock frequency is software configurable.
SD INTERFACE
SD
Data3-0
SD_DAT[3:0]
I/O8PU
These are bi-directional data signals.
These pins have internally controlled weak pull-up
resistors.
SD Clock
SD_CLK
O8
This is an output clock signal to SD/MMC device.
The clock frequency is software configurable.
NAME
SYMBOL
BUFFER
TYPE
DESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| USB2601-NU-04 | |
| USB3315-CP-TR | |
| USB3329C-GL-TR | |
| USB3321C-GL-TR | |
| USC-RCM5-J-006 | 50/125 um, MULTI MODE, SIMPLEX SC CONNECTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| USB2602-NU-05 | 功能描述:USB 接口集成電路 USB2.0 FLASH MEDIA CONTROLLER W/FET HS RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| USB2602-NU-06 | 功能描述:USB 接口集成電路 USB 2.0 Flash Media Cntrlr and 4Port Hub RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| USB2602-NU-XX | 制造商:SMSC 制造商全稱:SMSC 功能描述:4th Generation USB2.0 Flash Media Controller with Integrated Card Power FETs and HS Hub |
| USB260-E3/2CT | 功能描述:整流器 600 Volt 2.0A 30ns 90 Amp IFSM RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel |
| USB260-E3/52T | 功能描述:整流器 2.0 Amp 600 Volt RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。