- 您現在的位置：買賣IC網 > PDF目錄200642 > UPD23C8001EJGU-XXX-9KH x8 ROM (Mask Programmable) PDF資料下載
參數資料
| 型號： | UPD23C8001EJGU-XXX-9KH |
| 英文描述： | x8 ROM (Mask Programmable) |
| 中文描述： | x8光盤（掩模可編程） |
| 文件頁數： | 7/16頁 |
| 文件大?。?/td> | 151K |
| 代理商： | UPD23C8001EJGU-XXX-9KH |
15
PD23C128000L
Data Sheet M13644EJ3V0DS00
NOTES FOR CMOS DEVICES
1
PRECAUTION AGAINST ESD FOR SEMICONDUCTORS
Note:
Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and
ultimately degrade the device operation. Steps must be taken to stop generation of static electricity
as much as possible, and quickly dissipate it once, when it has occurred. Environmental control
must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using
insulators that easily build static electricity. Semiconductor devices must be stored and transported
in an anti-static container, static shielding bag or conductive material. All test and measurement
tools including work bench and floor should be grounded. The operator should be grounded using
wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need
to be taken for PW boards with semiconductor devices on it.
2
HANDLING OF UNUSED INPUT PINS FOR CMOS
Note:
No connection for CMOS device inputs can be cause of malfunction. If no connection is provided
to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence
causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels
of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused
pin should be connected to VDD or GND with a resistor, if it is considered to have a possibility of
being an output pin. All handling related to the unused pins must be judged device by device and
related specifications governing the devices.
3
STATUS BEFORE INITIALIZATION OF MOS DEVICES
Note:
Power-on does not necessarily define initial status of MOS device. Production process of MOS
does not define the initial operation status of the device. Immediately after the power source is
turned ON, the devices with reset function have not yet been initialized. Hence, power-on does
not guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the
reset signal is received. Reset operation must be executed immediately after power-on for devices
having reset function.
相關PDF資料 |
PDF描述 |
|---|---|
| UPD23C8001EJGW-XXX | x8 ROM (Mask Programmable) |
| UPD26401GU-XXX-9JH | SRAM/ROM |
| UPD26401GU-XXX-9KH | SRAM/ROM |
| UPD26411GZ-XXX-KJH | SRAM/ROM |
| UPD26411GZ-XXX-KKH | SRAM/ROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UPD23C8001EJGW-XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 ROM (Mask Programmable) |
| UPD2415 | 功能描述:固態繼電器-PCB安裝 UPD Single-Phase 240V / 15A ZC PCB RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| UPD2415_12 | 制造商:CRYDOM 制造商全稱:Crydom Inc., 功能描述:PCB Mount |
| UPD2415-10 | 功能描述:固態繼電器-PCB安裝 UPD Single-Phase 240V / 15A Ran PCB RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| UPD2415D | 功能描述:固態繼電器-PCB安裝 UPD Dual Output 240V / 15A ZC PCB RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。