- 您現在的位置：買賣IC網 > PDF目錄383978 > UPC659A (NEC Corp.) 8-BIT A/D CONVERTER FOR VIDEO PROCESSING WITH REFERENCE GENERATOR AND CLAMP CIRCUIT PDF資料下載
參數資料
| 型號： | UPC659A |
| 廠商： | NEC Corp. |
| 英文描述： | 8-BIT A/D CONVERTER FOR VIDEO PROCESSING WITH REFERENCE GENERATOR AND CLAMP CIRCUIT |
| 中文描述： | 8位A / D的視頻與參考發生器和鉗位電路處理轉爐 |
| 文件頁數： | 11/16頁 |
| 文件大小： | 123K |
| 代理商： | UPC659A |
11
μ
PC659A
ATTENTION FOR APPLICATION
Converted data output
Analog signal is captured at the rising edge, and converted data will be output at the rising edge after 1 clock pulse.
For the
μ
PC659, 2 clock pulses.
Analog input terminal
In case the pedestal level is clamped, the clamp circuit uses the soft clamp circuit to protect the burst level. However,
if a high impedance output is connected to the V
IN
pin (pin 4), the burst level will be reduced (for example, for an
external impedance of 10
, the burst level is reduced by approx. 3 %).
Therefore, connect the lowest possible impedance signal to the analog signal input pin.
Clamp pulse
Low output
impedance
buffer
P
CL
Clamp voltage
V
CL
AGND
PC659A
μ
V
IN
4
6
7
If don’s use the clamp circuit
P
CL
pin (pin 6) and GND must be short-circuit. And insert by-pass capacitor of about 0.1
μ
F between the V
CL
pin
(pin 7) and GND. Input analog signal to V
IN
pin (pin 4).
In case an external clamp circuit is used, connect the P
CL
pin (pin 6) to GND, and leave the V
CL
pin (pin 7)
unconnected. Set the voltage of the V
IN
pin (pin 4) between 2.3 V and 3.3 V.
Clamp voltage
There is a few difference clamp voltage between the supply clamp voltage V
CL
(pin 7) and really clamp voltage.
Really clamp voltage = V
CL
+
α
Take account of the
α
(about
±
20 mV) at supply V
CL
to pin 7.
When reference voltage is set from external, V
RB
(pin 10) = 2.3 V, V
RT
(pin 1) = 3.3 V .
Circuit current
TYP. (Unit: mA)
Analog circuit current
37
Digital circuit current
6
Sum
43
Set the sampling clock frequency between 1 MHz and 20 MHz. If a frequency outside this range is used, the internal
sample-and-hold circuit will not function properly.
First apply 5 V to the AV
CC
pins (pins 3 and 11) and the DV
CC
pin (pin 18), then input the analog signal to the V
IN
pin (pin 4). If the analog signal is input first, the output data may latch up.
相關PDF資料 |
PDF描述 |
|---|---|
| UPC659AGS | 8-BIT A/D CONVERTER FOR VIDEO PROCESSING WITH REFERENCE GENERATOR AND CLAMP CIRCUIT |
| UPC667 | 10-BIT D/A CONVERTER |
| UPC667CT | 10-BIT D/A CONVERTER |
| UPC8110GR | 1 GHz QUADRATURE MODULATOR |
| UPC8110GR-E1 | 1 GHz DIRECT QUADRATURE MODULATOR FOR DIGITAL MOBILE COMMUNICATION |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UPC659AGS | 制造商:Renesas Electronics Corporation 功能描述: 制造商:Panasonic Industrial Company 功能描述:IC |
| UPC659G | 制造商:Panasonic Industrial Company 功能描述:IC |
| UPC660C | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter， 6-Bit |
| UPC660G | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter， 6-Bit |
| UPC661CA | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter， 6-Bit |
發布緊急采購，3分鐘左右您將得到回復。