- 您現在的位置：買賣IC網 > PDF目錄382717 > UC2584DW Analog IC PDF資料下載
參數資料
| 型號： | UC2584DW |
| 英文描述： | Analog IC |
| 中文描述： | 模擬IC |
| 文件頁數： | 5/7頁 |
| 文件大?。?/td> | 180K |
| 代理商： | UC2584DW |
5
UC1584
UC2584
UC3584
Edge Modulation
During normal operation the oscillator must be synchro-
nized to the falling edge of the transformer secondary
waveform. Synchronization is achieved by connecting
SYNC to the secondary winding via a resistor divider.
The resistor divider must be chosen to provide a SYNC
pin voltage in excess of 1V at the lowest operating volt-
age on the transformer secondary winding. The UC3584
will generate a narrow internal synchronization pulse
which will synchronize the oscillator to the switching fre-
quency of the main converter.
PWM and Output Driver
The UC3584 employs leading edge modulation tech-
nique to set the required on time of its output. Leading
edge modulation is preferred for secondary side regula-
tion in multiple output converters to prevent ambiguity in
the primary current waveform. In fact, this is the only fea-
sible technique to preserve compatibility with primary
side peak current mode control.
As Fig. 1 depicts the UC3584 utilizes voltage mode con-
trol to regulate output voltage. The output pulse width
(the on-time of the MOSFET switch) is determined on a
cycle-by-cycle basis by comparing the output of the volt-
age error amplifier and the ramp waveforms across the
timing capacitor. OUT is asserted when the voltage on
COMP exceeds the voltage on CT. There are three more
conditions which must be satisfied to obtain an active
high on the OUT pin. These conditions are:
1. VCC within normal range (UVLO is inactive),
2. No fault condition is detected,
3. C
T
is discharging.
During the fast charging time of the C
T
capacitor is held
low.
Ultimately, the output of the PWM circuitry controls the
conduction interval of an external N-channel MOSFET
switch in the power supply. The UC3584 employs an
on-board, floating gate driver circuit to interface to the
external switch. An external capacitor connected be-
tween VFLT and SRC acts as a floating power supply for
V
SEC
C
T
OUT
COMP
INTERNAL
SYNC PULSE
Figure 1. Trailing edge synchronization, leading edge modulation.
APPLICATION INFORMATION (cont.)
UDG-99064
1.E+04
1.E+05
1.E+06
1.E+03
1.E+04
1.E+05
TIMING RESISTOR (Ohms)
F
47pF
100pF
220pF
470pF
1000pF
1200pF
1500pF
Figure 2. Oscillator frequency vs. R
T
with C
T
as a
parameter.
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相關PDF資料 |
PDF描述 |
|---|---|
| UC2584N | ISO HIGH SIDE SMART POWER SOLID STATE RELAY |
| UC1584J | 8-bit MCU for automotive with Flash or ROM, 10-bit ADC, 5 timers, SPI, LINSCI", active CAN |
| UC2610DW | BRIDGE/RING DIODE ARRAY|SO |
| UC2610DWTR | High side smart power solid state relay |
| UC2610J | High side smart power solid state relay |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UC2584N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| UC2-5NJ | 功能描述:低信號繼電器 - PCB DPDT NL 5VDC RoHS:否 制造商:NEC 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 V 最大開關電流:1 A 線圈電流:1 A 線圈類型:Non-Latching 功耗:140 mW 端接類型:SMT 絕緣: 介入損耗: |
| UC2-5NU | 制造商:IMO Precision Controls Ltd 功能描述:RELAY DPCO 5V 制造商:NEC Electronics Corporation 功能描述:SIGNAL RELAY DPDT 5VDC 1A THROUGH HOLE 制造商:IMO PRECISION CONTROLS 功能描述:RELAY, DPCO, 5V 制造商:NEC Electronics Corporation 功能描述:SIGNAL RELAY DPDT 5VDC, 1A, THROUGH HOLE 制造商:IMO Precision Controls Ltd 功能描述:RELAY, DPCO, 5V; Coil Type:DC; Contact Configuration:DPCO; Contact Current Max:1A; Contact Voltage AC Nom:250V; Contact Voltage DC Nom:220V; Coil Voltage VDC Nom:5V; Coil Resistance:178ohm; Coil Power Cont:140mW; Relay ;RoHS Compliant: Yes 制造商:NEC Electronics Corporation 功能描述:SIGNAL RELAY DPDT 5VDC, 1A, THROUGH HOLE; Coil Type:DC; Contact Configuration:DPDT; Contact Current Max:1A; Contact Voltage AC Nom:125V; Contact Voltage DC Nom:30V; Coil Voltage VDC Nom:5V; Coil Resistance:178ohm ;RoHS Compliant: Yes 制造商:World Products 功能描述:Electromechanical Relay DPDT 1A 5VDC 178Ohm Through Hole |
| UC2-5NU | 制造商:IMO Precision Controls Ltd 功能描述:RELAY DPCO 5V |
| UC2-5SNJ | 功能描述:低信號繼電器 - PCB DPDT SNGL COIL 5VDC RoHS:否 制造商:NEC 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 V 最大開關電流:1 A 線圈電流:1 A 線圈類型:Non-Latching 功耗:140 mW 端接類型:SMT 絕緣: 介入損耗: |
發布緊急采購，3分鐘左右您將得到回復。