- 您現在的位置：買賣IC網 > PDF目錄382702 > U2350B-FP PWM Speed Control for Permanent Excited DC Motors PDF資料下載
參數資料
| 型號： | U2350B-FP |
| 英文描述： | PWM Speed Control for Permanent Excited DC Motors |
| 中文描述： | PWM調速永久激直流電動機控制 |
| 文件頁數： | 4/9頁 |
| 文件大?。?/td> | 118K |
| 代理商： | U2350B-FP |
U2350B-FP
TELEFUNKEN Semiconductors
Rev. A1, 29-May-96
4 (9)
The output stage logic now brings V
14
to low potential
and closes the switching output Pin 10. This has the effect
of discharging C
1
via R
9
and the switch S
1
until the
approximately 300 mV hysteresis of the comparator is
completed. The discharge time is dependent on the
control voltage V
8
.
Comp. 1 then switches over again and the cycle begins
once more (see figure 3). This two-state controller
compensates the influence of the mains voltage, with the
result that the motor voltage or motor speed is largely
determined by the magnitude of the control voltage.
Current Control, Pin 11
If the current flowing through the IGBT (or MOSFET)
and the shunt resistor R
8
becomes so high that a voltage
higher than 1.5 V arises at Pin 11, a second control loop
formed with the comparator Comp. 2 becomes active,
and overrides the first control loop via an AND gate. This
causes the average value of the current, fed to the motor,
to be controlled to a constant value. This in turn results in
a speed which decreases greatly with the increasing
torque (see figure 4).
V
9
V
10
V
14
t
95 10869
Figure 3. Pulse width control signal characteristics
Speed
(of rotation)
Torque
V
8
I
max
95 10870
Figure 4. Influence of current control on the characteristic
(curve) of a motor
By exceeding the maximum current which is adjustable
with R
8
, the control dependent voltage V
8
(shunt
characteristic)
reaches
the
characteristic). By applying a current which depends on
the load voltage across R
6
, the constant value of the
current can be further influenced. In addition, the current
control limits the starting current.
dotted
lines
(series
In the case of effective current limiting, alteration of the
rectified mains voltage has an effect on the power taken
up. In order to compensate for this influence, the resistor
R
7
is connected to Pin 11. If dimensioned appropriately,
the consumed power is independent of changes in the
mains voltage within a wide range of this voltage.
Operation Mode Selection, Pin 5
It is possible to program three modes of operation with the
tristate input, as follows:
a)
Intermittent operation (Pin 5 connected to +V
S
)
A signal emitted by an internal oscillator (see
figure 5) switches the output stage ON and OFF
periodically via S
2
. This intermittent operation is
very suitable for certain uses.
b) Stop function (Pin 5 open)
The output is continuously switched off, the motor is
at reset.
c)
Normal function (Pin 5 connected to V
12
)
The motor runs continuously.
Temperature Monitoring, Pin 4
The circuit also has a monitoring input. If a NTC-resistor
is connected to this input, for example, it functions as a
temperature sensor. If the voltage V
4
falls below the first
threshold V
T80
(approximately 420 mV) as a result of the
increasing temperature, an external LED D
3
, which is
connected between Pin 1 and Pin 2, starts to blink. If the
temperature increases further and the voltage V
4
falls
below a second threshold V
T100
(approximately
350 mV), a latch is set. The latch makes this LED light up
continuously, the output stage is blocked. The motor is
switched-OFF and remains switched-OFF until the
temperature has fallen and until the mains voltage is
switched-OFF and switched-ON again (the latch is solely
reset by the voltage monitoring). A second LED D
2
,
which is connected between Pin 2 and Pin 16 and which
is continuously illuminated (switch-ON) during normal
operation, is switched-OFF.
In the event of wire breakage in the sensor branch, Pin 4
is pulled up to +V
S
. After the switch-OFF threshold
V
TOFF
(approximately V
S
–1.8 V) has been exceeded, the
circuit ensures that the latch is set here too. This
guarantees safe operation.
相關PDF資料 |
PDF描述 |
|---|---|
| U2352 | PWM Power Control for DC Loads |
| U2352B | PWM Power Control for DC Loads |
| U2391B | Quartz Controlled Pulse Generator |
| U243B-FP | Warning or Car-Direction Indicator |
| U2642B | Intermittent- and Wipe/Wash Control for Wiper Systems |
相關代理商/技術參數 |
參數描述 |
|---|---|
| U2351A | 制造商:Agilent Technologies 功能描述:Bulk 制造商:Agilent Technologies 功能描述:DATA ACQUISITION MODULE 16 CHANNEL 制造商:Agilent Technologies 功能描述:USB MODULAR DATA ACQUISITION; No. of Channels:16; Sampling Rate:1MSPS; Input Voltage Max:12V; Input Current Max:10A; Bandwidth:400kHz; External Height:44mm; External Width:120mm; External Depth:182.4mm; Sample Rate:250 kSa/s ;RoHS Compliant: NA 制造商:Agilent Technologies 功能描述:16-Channel 250kSa/s USB Data Acquisition |
| U2352 | 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:PWM Power Control for DC Loads |
| U2-352 | 制造商:OTTO Engineering Inc 功能描述:S/A U2-270 EX W/ |
| U2352A | 制造商:Agilent Technologies 功能描述:DATA ACQUISITION MODULE 16 CHANNEL 制造商:Agilent Technologies 功能描述:DATA ACQUISITION MODULE, 16 CHANNEL 制造商:Agilent Technologies 功能描述:USB MODULAR DATA ACQUISITION; No. of Channels:16; Sampling Rate:1MSPS; Input Voltage Max:12V; Input Current Max:10A; Bandwidth:400kHz; External Height:44mm; External Width:120mm; External Depth:182.4mm; Sample Rate:250 kSa/s ;RoHS Compliant: NA 制造商:Agilent Technologies 功能描述:16-Channel 250kSa/s USB Data Acquisition |
| U2352B | 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:PWM Power Control for DC Loads |
發布緊急采購，3分鐘左右您將得到回復。