- 您現在的位置：買賣IC網 > PDF目錄382702 > U211B2 Phase Control Circuit - General Purpose Feedback PDF資料下載
參數資料
| 型號： | U211B2 |
| 英文描述： | Phase Control Circuit - General Purpose Feedback |
| 中文描述： | 相位控制電路-通用信息反饋 |
| 文件頁數： | 3/20頁 |
| 文件大小： | 322K |
| 代理商： | U211B2 |
U211B2/ B3
TELEFUNKEN Semiconductors
Rev. A1, 29-May-96
3 (20)
Description
Mains Supply
The U211B2 is fitted with voltage limiting and can
therefore be supplied directly from the mains. The supply
voltage between Pin 2 (+ pol/
across D
1
and R
1
and is smoothed by C
1
. The value of the
series resistance can be approximated using (see
figure 2):
) and Pin 3 builds up
R
1
V
M
– V
S
2 I
S
Further information regarding the design of the mains
supply can be found in the data sheets in the appendix.
The reference voltage source on Pin 16
of typ. –8.9 V is
derived from the supply voltage and is used for
regulation.
Operation using an externally stabilised DC voltage is not
recommended.
If the supply cannot be taken directly from the mains
because the power dissipation in R
1
would be too large,
then the circuit shown in the following figure 3 should be
used.
1
2
3
4
5
C
1
R
1
24 V~
~
95 10362
Figure 3. Supply voltage for high current requirements
Phase Control
There is a general explanation in the data sheet,
TEA1007, on the common phase control function. The
phase angle of the trigger pulse is derived by comparing
the ramp voltage (which is mains synchronized by the
voltage detector) with the set value on the control input
Pin 12. The slope of the ramp is determined by C
2
and its
charging current. The charging current can be varied
using R
2
on Pin 6. The maximum phase angle
max
can
also be adjusted using R
2
.
When the potential on Pin 7 reaches the nominal value
predetermined at Pin 12, then a trigger pulse is generated
whose width t
p
is determined by the value of C
2
(the value
of C
2
and hence the pulse width can be evaluated by
assuming 8 s/nF). At the same time, a latch is set, so that
as long as the automatic retriggering has not been
activated, then no more pulses can be generated in that
half cycle.
The current sensor on Pin 1 ensures that, for operations
with inductive loads, no pulse will be generated in a new
half-cycle as long as a current from the previous half
cycle is still flowing in the opposite direction to the
supply voltage at that instant. This makes sure that “gaps”
in the load current are prevented.
The control signal on Pin 12 can be in the range 0
V to
–7 V (reference point Pin 2).
If V
12
=
–7 V then the phase angle is at maximum
= max
i.e., the current flow angle is a minimum. The phase angle
min
is minimum when V
12
= V
2
.
Voltage Monitoring
As the voltage is built up, uncontrolled output pulses are
avoided by internal voltage surveillance. At the same
time, all of the latches in the circuit (phase control, load
limit regulation, soft start) are reset and the soft-start
capacitor is short circuited. Used with a switching
hysteresis of 300 mV, this system guarantees defined
start-up behavior each time the supply voltage is switched
on or after short interruptions of the mains supply.
Soft-Start
As soon as the supply voltage builds up (t
1
), the integrated
soft-start is initiated. The figure below shows the
behaviour of the voltage across the soft-start capacitor
and is identical with the voltage on the phase control input
on Pin 12. This behaviour guarantees a gentle start-up for
the motor and automatically ensures the optimum run-up
time.
相關PDF資料 |
PDF描述 |
|---|---|
| U211B3 | Phase Control Circuit - General Purpose Feedback |
| U2270B | Read / Write Base Station IC |
| U2305B | VHF/ UHF-Tuner-IC |
| U2305B-AFSG3 | VHF/ UHF-Tuner-IC |
| U2320B | VHF/UHF Tuner-IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| U211B3 | 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:Phase Control Circuit - General Purpose Feedback |
| U211B-M | 功能描述:IC PHASE CONTROL TACHO 18-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 產品變化通告:ATA683(3,4)PLQW Obsolescence 09/Aug/2012 標準包裝:1 系列:- 應用:DC 電機控制器，無刷（BLDC），3 相 評估套件:可供 輸出數:1 電流 - 輸出:100mA 電壓 - 負載:5.25 V ~ 20 V 電源電壓:5.25 V ~ 20 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-VQFN（7x7） 包裝:剪切帶 (CT) 其它名稱:ATA6833-PLQWCT |
| U211B-MFP | 功能描述:IC PHASE CONTROL TACHO 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 產品變化通告:ATA683(3,4)PLQW Obsolescence 09/Aug/2012 標準包裝:1 系列:- 應用:DC 電機控制器，無刷（BLDC），3 相 評估套件:可供 輸出數:1 電流 - 輸出:100mA 電壓 - 負載:5.25 V ~ 20 V 電源電壓:5.25 V ~ 20 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-VQFN（7x7） 包裝:剪切帶 (CT) 其它名稱:ATA6833-PLQWCT |
| U211B-MFPG3 | 功能描述:IC PHASE CONTROL TACHO 16-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 標準包裝:1 系列:- 應用:直流電機驅動器，步進電機驅動器 評估套件:- 輸出數:1 或 2 電流 - 輸出:750mA 電壓 - 負載:10 V ~ 40 V 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-BFSOP（0.295"，7.50mm 寬） 供應商設備封裝:24-SOP 包裝:Digi-Reel® 其它名稱:MTS62C19A-HS105DKR |
| U211B-MFPG3Y | 功能描述:馬達/運動/點火控制器和驅動器 Phase Sw/Control w/ Tacho overld limit RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。