- 您現在的位置：買賣IC網 > PDF目錄366059 > TZA3040 (NXP Semiconductors N.V.) SDH/SONET data and clock recovery unit STM1/4 OC3/12 PDF資料下載
參數資料
| 型號： | TZA3040 |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | XO, clock |
| 英文描述： | SDH/SONET data and clock recovery unit STM1/4 OC3/12 |
| 中文描述： | SDH / SONET的數據和時鐘恢復單元STM1 / 4 OC3/12 |
| 文件頁數： | 14/54頁 |
| 文件大?。?/td> | 1852K |
| 代理商： | TZA3040 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
14
Fiber optic transceiver board STM1/4/8,
OC3,12,24, FC/GE
Philips Semiconductors
Application Note
AN98090
1.4.3
Mounting of the laserdiode
Standard, the board is tested electrically. The bias & modulation source are then terminated to VCC with a
dummy load. After test pass, these resistors are removed.
Fig.3 Enlargement of the transmitter section. The top layer is shown in top view. The picture shows the footprint of the used
laser with corresponding pin-functionality.
1.4.4
Supply voltages
Standard, the board is tested on 5.0 V supply voltages. The supply voltages selectors on the bottom side of the
PCB are set to this.
If other voltages are required, please follow the description in section 3.3.
1.4.5
Back to back sensitivity measurement: Laserdriver in - DCR out
In this measurements 2 aspects have to be taken into account:
1.
Polarity inversion in the path from SMA connectors to light output
The SMA connectors LDR DIN / LDR DINQ are connected via a resistive splitter to the outputs of the
multiplexer (TXDQ / TXSD) and the inputs of the laserdriver (DIN/DINQ). When the multiplexer is turned off,
the signal on the connector drives the corresponding laserdriver inputs (LDR DIN - DIN and LDR DINQ -
DINQ).
Note that the “Q” output of the multiplexer is connected to the “normal” input of the laserdriver. The
laserdriver inverts the output of the multiplexer!
To correct for this, the LAQ output is connected to the laser, and the LA output can be monitored at the SMA
connector LA.
IF A PATTERN GENERATOR OUTPUT IS CONNECTED WITH THE ‘LDR DIN/LDR DINQ’ INPUTS, A
SIGNAL INVERSION OCCURS. THIS SHOULD BE TAKEN INTO ACCOUNT WHEN PERFORMING A BIT
ERROR TEST.
2.
Turning off the output of the multiplexer & keeping the 19 MHz from the synthesizer
The test signal STOPTX from the multiplexer TZA3005 turns both the output stages and the synthesizers
1
2
3
4
5
6
7
8
9
10
12
13
14
11
θ
Peltier
cathode
anode
TOP VIEW
相關PDF資料 |
PDF描述 |
|---|---|
| TZA3001AHL | SDH/SONET STM4/OC12 laser driver(SDH/SONET STM4/OC12 激光驅動器) |
| TZA3001A | SDH/SONET STM4/OC12 laser driver(SDH/SONET STM4/OC12 激光驅動器) |
| TZA3005 | SDH/SONET STM1/OC3 and STM4/OC12 transceiver |
| TZA3023 | SDH/SONET STM4/OC12 transimpedance amplifier |
| TZA3023T | SDH/SONET STM4/OC12 transimpedance amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TZA3041 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Gigabit Ethernet/Fibre Channel laser drivers |
| TZA3041AHL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Gigabit Ethernet/Fibre Channel laser drivers |
| TZA3041BHL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Gigabit Ethernet/Fibre Channel laser drivers |
| TZA3041U | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Gigabit Ethernet/Fibre Channel laser drivers |
| TZA3043 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Gigabit Ethernet/Fibre Channel transimpedance amplifier |
發布緊急采購，3分鐘左右您將得到回復。